Pro-Ject Audio Systems Box-Design MaiA S3 Скачать руководство пользователя страница 5

© Pro-Ject Audio Systems · MaiA S3 · Revision 2022.01.03 

 

5

 

Technical specifications Pro-Ject MaiA S3 

Power output: 

2x 23W/40W at 8 ohms/4 ohms (1%THD) 

Frequency response (20Hz-20kHz): 

<- 0,5dB (@4ohm) 

Channel separation:  

- 69dB at 10kHz 

Signal to noise ratio PA output: 

97dB (101 dB - 'A' weighted) at 4ohm 

Signal to noise ratio Variable output: 

103dB (105 dB - 'A' weighted) 

THD: 

< 0,04% at 10W / 4 ohms 

Headphone amplifier output:  

2x 75mW at 32ohm (1%THD) 

Line level inputs: 

3 pair RCA (sensitivity: 270 mV) 

Line input impedance: 

50kohms 

Line input gain: 

33,5dB 

Phono input: 

1 pair RCA  

Phono input sensitivity: 

suitable for MM, MI or high output MC cartridges 

Phono input impedance: 

47kohms 

Phono input gain: 

46dB 

S/PDIF coaxial input: 

up to 24bit and 192kHz 

S/PDIF optical input: 

2 inputs - up to 24bit and 192kHz 

Digital to Analogue converter: 

Cirrus Logic CS4344 24bit/192kHz Multi-bit Delta Sigma type 

Variable line level output: 

1 pair RCA 

BT version: 

5.0 

BT music receiver codec: 

aptX, aptX HD, A2DP profile 

BT maximum TX power: 

+4dBm 

Speakers connectors: 

∅ 

4mm banana plugs, spades connectors or naked wire 

Headphone output: 

 

          6,3mm jack (16 – 600ohms) 

Outboard power supply: 

20V/3A DC, suitable for your country's mains supply 

Power consumption in standby: 

<0.5W 

Replacement battery remote control: 

1 x CR2032 / 3V or 1 x CR2025 / 3V 

Dimensions W x H x D (D with sockets):  206 x 55 x 153 (176) mm 
Weight: 

1070 g without power supply 

 
Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for 
further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible 
distributor in your country. 

Warranty 

 

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 
for use. Modification or changes to any part of the product by unauthorized persons release the 
manufacturer from any liability over and above the lawful rights of the customer. 

Copyright, trademarks 

Pro-Ject Audio Systems is a registered Trademark of     
H. Lichtenegger. 

This guide was produced by: Pro-Ject Audio Systems 
Copyright 

©

 2022. All rights reserved.

 

 

The information was correct at the time of going to 
press. The manufacturer reserves the right to make 
changes to the technical specification without prior 
notice as deemed necessary to uphold the ongoing 
process of technical development.

 

 
BT®, aptX and aptX HD  are  trademarks  owned by the BT  SIG Inc., Microsoft®, Windows®, are either 
registered trademarks or trademarks of Microsoft Corporation, Apple is registered trademark of Apple Inc., 
Android™ is a trademark of Google Inc. 
 

Содержание Box-Design MaiA S3







Отзывы: