manualshive.com logo in svg

Pro-Form CrossWalk LT, Руководство пользователя, Страница: 27 / 36

Поделиться
Скачать
Pro-Form CrossWalk LT Скачать руководство пользователя страница 27

27

SYMPTOM: The upper body arms squeak during 

use

a.  

  (Note: Correcting this problem requires a small 
amount of marine grease, available at hardware 
stores.) Turn the resistance knob (C) counterclock-
wise and remove it. Next, remove the resistance 
cone (D) and the upper body arm (E), along with 
the resistance plate (F), plastic spacer (G), spring 
washer (H), washers (I), and thrust bearing (J). 
(Note: If the resistance plate comes out of the 
resistance cone, press it back in.) Apply a thin layer 
of white marine grease to the outer surface of the 
resistance cone. Then reattach all parts in the order 
shown below.

SYMPTOM: The walking belt slows when walked on

a.  

  Use only a surge suppressor that meets all of the 
specifications described on page 16.

b.  

If the walking belt is overtightened, treadmill per-
formance may decrease and the walking belt may 
become damaged. Remove the key and 

UNPLUG 

THE POWER CORD.

 Using the hex key, turn both 

idler roller screws (K) counterclockwise, 1/4 of a 
turn. When the walking belt is properly tightened, 
you should be able to lift each edge of the walking 
belt 2 to 3 in. (5 to 7 cm) off the walking platform. 
Be careful to keep the walking belt centered. Plug 
in the power cord, insert the key, and start the 
walking belt at 1 mph. Walk on the treadmill and 
observe the walking belt. Repeat until the walking 
belt is properly tightened. 

Make sure to adjust 

the walking belt in small increments and to 
observe the walking belt for a minute after each 
adjustment.

c.  

Your treadmill features a walking belt coated with 
high-performance lubricant. 

IMPORTANT: Never 

apply silicone spray or other substances to 
the walking belt or the walking platform unless 
instructed to do so by an authorized service 
representative. Such substances may deterio-
rate the walking belt and cause excessive wear.

 

If you suspect that the walking belt needs more 
lubricant, see the front cover of this manual.

d.  

If the walking belt still slows when walked on, see 
the front cover of this manual.

D

E

C

F

G

H

J

I

a

K

K

2–3 in.

b

Содержание CrossWalk LT





































Отзывы:

Нет отзывов