DIAGRAM OF THE CONSOLE
• Misuse of this treadmill may cause serious injury. • Do not stand on
walking belt when starting treadmill. • Read User's Manual and follow
warnings and operating instructions. • Keep fluids off electronic console.
Pulse
Sensor
Incline
Control
Clip
Key
Speed Control
Monitor Displays
9
8
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning
on the power.
• Always wear the clip (see the drawing above)
whilst using the treadmill. When the key is re-
moved from the console, the walking belt will
stop.
• Adjust the speed in small increments.
• The training zones marked beside the speed
control are general guidelines only. See pages
14 and 15 for more information.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console. Use only a sealed water bottle.
BATTERY INSTALLATION
The console requires three “AA” batteries (not in-
cluded). Alkaline batteries are recommended.
To install batteries, open the battery cover under the
console as shown below. Press three batteries into the
battery com-
partment.
Make sure
that the neg-
ative (–)
ends of the
batteries are
touching the
springs.
Close the
battery cover.
STEP BY STEP CONSOLE OPERATION
Before operating the console, make sure that the power
cord is properly plugged in. (See HOW TO PLUG IN
THE POWER CORD on page 7.) If there is a thin sheet
of clear plastic on the face of the console, remove it.
Next, step onto the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
Follow the steps on page 9 to operate the console.
Batteries
Battery
Cover
Insert the key fully into the power switch.
Inserting the key will
not turn on the dis-
plays. The displays will
turn on when the
ON/RESET button is
pressed or when the
walking belt is started.
Note: If you just in-
stalled batteries, the displays will already be on.
Reset the speed control.
Slide the speed control
down to the RESET po-
sition. Note: Each time
the walking belt is
stopped, the speed
control must be moved
to the RESET position
before the walking belt
can be restarted.
Start the walking belt.
After you have moved the speed control to the
RESET position, slowly slide it upward until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin exer-
cising. Change the speed of the walking belt as de-
sired by sliding the speed control.
To stop the walking belt, step onto the foot rails and
slide the speed control to the RESET position.
Follow your progress with the monitor displays.
TIME display—This
display shows the total
time that you have
walked or run on the
treadmill.
DISTANCE display—
This display shows the
total distance that you
have walked or run.
SPEED display—This
display shows the speed
of the walking belt.
CALORIES/FAT CAL-
ORIES/PULSE
display—This display
shows the approximate
numbers of calories and
fat calories you have
burned. (See FAT
CALORIES on page 14 for an explanation of fat
calories.) Every seven seconds, the display will
change from one number to the other. Arrows in the
display will indicate which number is currently
shown. Note: This display will also show your pulse
when the pulse sensor is used.
The displays can be
reset, if desired, by
pressing the ON/RESET
button.
Measure your pulse, if desired.
To use the pulse
sensor, stand on
the foot rails and
place your thumb
on the pulse sen-
sor as shown. The
pulse sensor is
pressure-acti-
vated; fully press
down the pulse sensor. Do not press too hard, or
the circulation in your thumb will be restricted,
and your pulse will
not be detected. Next,
slightly raise your thumb
until the heart-shaped
indicator in the CALO-
RIES/ FAT CALO-
RIES/PULSE display
flashes steadily. Hold
your thumb at this level. After 5 to 10 seconds, your
pulse will be shown. Hold your thumb on the sensor
for another 15 seconds for the most accurate read-
ing. If the displayed pulse appears to be too high or
too low, or if your pulse is not displayed, lift your
thumb off the sensor and allow the display to reset.
Press down again on the sensor as described
above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure to the pulse sensor. Try the sensor sev-
eral times until you become familiar with it.
Remember to stand still whilst measuring your
pulse.
1
3
4
5
2
Arrows
Pulse
Sensor
Indicator
