Pro-face GP-2300 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 61

Pro-face GP-2300 Series Скачать руководство пользователя страница 34

GP-2300/2301 Series User Manual

3-1

Chapter

3 Installation and Wiring

1. Installation

2. Wiring Cautions

3. Tool Connector

3.1

Installation

3.1.1 Installation Procedures

4. Ethernet Cable Connector

5. CF Card Installation and Removal

Follow the steps given below when installing the GP.

Check the Installation Gasket’s Seating

It is strongly recommended that you use the installation gasket, since it absorbs

vibration in addition to repelling water.

Place the GP on a level surface with the display panel facing downward. Check
that the GP’s installation gasket is seated securely into the gasket’s groove, which
runs around the perimeter of the panel’s frame.

For details about installing the gasket, refer to

Installation

Gasket

GP

Rear face

• Before installing the GP into a cabinet or panel, check that the instal-

lation gasket is securely attached to the unit.

• A gasket which has been used for a long period of time may have

scraches or dirt on it, and could have lost much of its dust and drip
resistance. Be sure to change the gasket periodically (or when
scratches or dirt become visible).

• Be sure to use gasket model PS300-WP00.

• Be sure the gasket’s seam is not inserted into any of the unit’s cor-

ners, only in the straight sections of the groove. Inserting it into a
corner may lead to its eventually tearing.

6.1.2 Installation Gasket Check/Replacement

«
...
32
33
34
35
36
...
»

Содержание GP-2300 Series






























































Отзывы:

Нет отзывов