background image

5

4

Section 1: Boat Stand Assembly

There are 4 plywood boat stand pieces. The 2 short plywood 
pieces are the ends of the boat stand. 

Secure the 2 long plywood pieces of the interlocking boat stand to 
one end of the short plywood pieces. Repeat with the remaining 
short plywood pieces.

Secure the stand together where each piece is joined with epoxy 
or CA glue (not included).

Section 3: Installing the Radio System Batteries (cont.)

Section 4: Installing the Wing

Section 2: Removing the Canopy

Unscrew the 2 knurled hatch-mounting screws from the rear of 
the hatch. Slide the front hatch retainer toward the rear of the 
boat and lift the hatch from the boat.

Section 3: Installing the Radio System Batteries

Receiver Batteries

Remove the 10 2.5mm hex head screws that secure the clear 
Lexan radio box cover.

Remove the receiver battery holder and install 4 “AA” alkaline 
batteries in the battery holder. Note proper polarity. 

Reinstall the battery holder into the radio compartment.

Secure the radio box cover with the 6 Phillips screws. 

Transmitter Batteries

Remove the transmitter from the box.

Remove the battery cover on the bottom of the transmitter.

Insert 8 “AA” alkaline batteries into the battery holder. 
Note proper polarity.

Turn on the transmitter and confirm that the LCD illuminates, 
indicating proper installation of fully charged batteries. 

Turn on the receiver switch and move the controls. Confirm that 
all controls operate in the proper direction and are controlled by 
the proper transmitter input.

Turn the transmitter and the receiver switch off. To keep the boat 
from receiving stray signals, the transmitter should be turned on 
first, followed by the receiver. Likewise, the receiver should be 
turned off first, then the transmitter. 

Install the wing in the direction shown. 

Install the four 3mm x 20mm hex head screws and secure with 
the four 3mm nuts. 

 Apply screw-locking compound to the threads to lock the nuts  
in place.

NOTE: 

The wing is not intended to be a handle.

7672_PRB_shockwave55ss_manual2.indd   4-5

6/23/05   9:28:13 AM

Содержание ShockWave 55









Отзывы: