Prismasonic Cinoscreen F-100 Скачать руководство пользователя страница 4

Assembly Instructions

STEP 6 

(F-AT models only)

Connect the 

Black Mask Fabric 

onto the front side of framework by staples. Shoot one staple in about every 20 

cm, after which cut the fabric to match the framework size by scissors or carpet knife. It is not important how the 
back fabric looks as long as it covers the area inside the outer framework bars. Neither it does not have to be 100% 
tensed. 

(It will finally be covered by the actual screen fabric and the velvet frames anyway.)

STEP 7

Prepare to connect the 

Screen Fabric 

to 

Fabric 

Holder

s, which are inserted inside into the slots of 

framework bars, as shown in 

Fig 7a. 

Use 

Washer, 

10 mm 

and 

Nut, 10 mm 

to fasten the fabric. The 

Fabric Holder

s

 with a Plate 

are placed in each four 

corner 

(Fig 7b) 

STEP 10

Now the rest of 

Fabric Holder

s are inserted to 

Frame work 

bars, and the 

Screen Fabric

 is attached to those 

again exactly as shown in 

Fig 7a

. And after this those spots are also tightened according to instructions in 

Step 

9. 

If there still exist some loosen areas on screen the further tightening can still be performed, until the surface is 

perfectly flat.

Video Screen

Cinoscreen F-100 / F-AT100

Fig 7a 

(back view)

Fig 7b

Fig 8

STEP 8

Place the 

Fabric Holder

s first to the horizontal top frame work bars and to the top corners, after which, 

starting from corner, roll the fabric open and simultaneously string the tabs of fabric to every 

Fabric Holder 

on top corners and bars. After this insert the 

Fabric Holder

s also to the spots marked with the arrows in 

Fig 

8

. Now, exactly as presented in 

Fig 7a, 

lock the fabric to the holders, 

BUT FIRST ONLY FROM THE SPOTS 

MARKED WITH ARROWS IN FIG 8

, even if the top bars already have the rest of holders in their place. 

Tighten the ten nuts securely by using the 

Spanner Wrench.

NOTE! 

With F-AT model place the two white woven fabrics, one after another on top with each other, so that the 

one with a diagonal surface pattern stays on top.

Fig 9

STEP 9

The fabric is now tightened first from the spots 
marked with arrows in 

Fig 8. 

Using the 

L-

Wrench, 3mm, 

screw the

 

set screws inside the 

Fabric Holders 

clock wise

each for 4-5 full turns.

Before tightening make sure that in every four 
corner the fabric tabs bends entirely over the 
front edge of the fabric holder plate, exactly as 
shown with arrows in 

Fig 9

Care and Maintenance 

(

CinoWhite and CinoAT Fabrics)

Clean surface with a solution of mild dishwashing liquid 
diluted with warm water. Sponge the surface, rinse with clear 
water and blot dry. It is also possible to use cleaning solvents 
or abrasives.

Fig 11 

(back view)

a)

a)

b)

STEP 11 
Velvet Frame

s are now attached to the framework bars. First prepare to connect the two 

Frame Holder

s to the 

side threads of each six velvet frame parts with 

Cap Screw m6 x 16 (Fig 11a)

. Similarly attach the frame holder 

assembly 

(Fig 2h and Fig 11b)

 to each center thread of velvet frame. Tighten all screws securely by using 

L-

Wrench 4 mm. 

Finally, repeating this for all six velvet frames, string the 

Frame Holder

s in side to the set screws, 

assembled in 

Step 2 (Fig 2f and 2g)

, and connect the center 

Frame Holder 

with a plate onto the slot in the 

framework bar using the 

Torx Screw

Tighten the screws of each velvet frame securely using the 

Screw Driver,

 

torx. 

Still match the joints of frames perfectly to each other and 

You’re done.       ...  

Enjoy your new 2.40:1 picture!

NOTE: 

 If the motorized mask system is also installed, 

do not perform the step 11,

 but start to follow the user manual 

of

 

Cinomask F-100.

Отзывы: