Printer Setup
Many of the printer’s features may be set using menus available on the front panel of the printer.
For complete details, please refer to the MtP400 Series Operator’s Manual.
To enter the Setup Mode, press and hold the Enter Button while turning on the printer with the
Power Button. Continue to hold the
Enter Button until “Menus Active” is displayed in the LCD Message Window.
While in Setup Mode, the power indicator will blink slowly. Upon entering Setup Mode, the FORMAT MENU is shown first. To advance
to the INTERFACE MENU or OPTIONS MENU, press the Advance Button.
When in Setup Mode, the current menu item is shown on the top line in the LCD Message Window, and its corresponding value is shown
on the bottom line. To increment the value on the bottom line to the next setting, press the Increment Button. To advance to the next
menu item, press the Enter Button.
To exit Setup Mode, press the Advance Button until “Exit Setup” is displayed. Press the Enter Button to save the changes and
return to normal printer operation.
Indicators:
Power On = Ready to print, Slow Flash = Setup Mode,
Short Flash = Power Saving Stand By Mode.
Wireless I/O Enabled and Connected.
Magnetic Card Reader: Ready for swipe.
Error: See messages, below.
Battery: On = Charging, Flashing = Battery Low.
Printer Setup Menus
(Default Values Shown)
•
Use the Advance Button to access the next menu.
•
Use the Increment Button to increment the value displayed on the bottom line.
•
Use the Enter Button to accept the value displayed and advance to the next item.
Paper Related LCD Messages:
Paper Door Open - Close paper door and press
the
Paper Feed
Button to
continue.
Paper Fault - Insert paper or correct jam
and press the
Paper Feed
Button to continue.
Magnetic Card Reader LCD Messages:
Swipe Card Now - Magnetic Card Reader is
ready for card to be swiped.
Card Read Ok - Card read successfully.
Card Not Read - Card not read correctly.
INTERFACE MENUS
IMAGE MANAGEMENT
DEVICE SETTINGS
Serial
Bluetooth **
Print Contrast = 0
Default Font = 16.9 Courier
Scalable Font = Default Scalable
Resident Font = Default Resident
Char Placement = Fixed Width
Char Space (%) = 0
Line Spacing = 3
Long Lines = Wrap
Left Margin = 0
Right Margin = 0
Max Paper Speed = 3.30 ips
Form Feed Ctrl = Distance
(Back Mark*)
FFeed Distance = 1.2608”
Top of Form Adj = 0.0000”
Tear Adj = 0.0000”
Mark Sensitivity = 0
Emulation = Printek
Baud Rate = 57600
Parity = None
Data Bits = 8
Stop Bits = 1
XON/XOFF = Off
ETX/ACK = Off
RTS/CTS = On
Emulation = Printek
Pairing Mode = Paired
Role Policy = Defer
Discoverability = On
Pin = “0”
Security = Off
Local Name = MtP300-Serial#
Address = (Hardware Value)
IrDA **
Wi-Fi **
ADVANCED
Emulation = Printek
Emulation = Printek
Pass Thru Mode = Off
Basic Network Settings:
(Requires Mobile Setup Utility at right)
SSID = Any
Type = Ad-Hoc
Channel = 1
Encryption = Open
Authentication = Open PSK
Auth Protocol = PAP
Use WEP Key # = 1
IP Method = DHCP
Address = 192.0.0.192
Subnet = 255.255.255.0
Gateway = 192.0.0.1
Printer Server Port = 8023
Auto Power Down = Off
Print Header = Not Loaded
Print Promotion = Not Loaded
Reprint Mode = Disabled
MCR Method = Host Request
MCR Data = 1 Track
Note: After exiting Setup, you may print the current Interface settings by
pressing and holding the Enter Button until “Printing Setup” is
displayed.
** IrDA, Bluetooth, or Wi-Fi are only available if installed.
To switch between these interfaces and the Serial Interface, press
and hold the Enter Button until “Interface Now …” is displayed.
Mobile Setup Utility
In addition to using the Printer’s Front Panel Setup
as described at the left, a Mobile Setup Utility is
available that allows the printer to be configured
from a Windows
®
desktop operating system or
from a Windows Mobile
®
, Windows CE, or Pocket
PC device.
For information regarding the Mobile Setup utility,
please contact your system administrator.
Please Note: The Mobile Setup utility is required
to make changes to the network settings of the
Wi-Fi interface.
Setup utilities, printer drivers and the USB cable driver may be
downloaded from printekmobile.com.
Printek is a registered trademark of Printek, Inc.
Windows and Windows Mobile are registered trademarks of
Microsoft Corp.
Note: Based on Firmware Version 6.1.d. If your printer uses a different version, older documents are available at printekmobile.com.
Printek Part Number 7084 Rev. A
Power
LCD Message Window
Increment
Paper Feed
/Advance
IrDA Window
Enter
