Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 91

Страница: 91 / 122

Chapter 10

Troubleshooting

Once the driver installation has been completed, it may be necessary to reboot the
computer.

If prompted for a reboot, select:

•

Yes

to reboot the host computer immediately, or

•

to delay rebooting the computer until a later time.

When delaying the reboot, dismiss/close the

eBUS Driver Installation Tool

dialog.

Once the computer has been rebooted, verify that the network connection has been
established.

10.6.2 LightField Applications

Perform the following procedure to restore an Ethernet network connection for LightField
applications:

Navigate to the directory in which the

EbDriverTool64.exe

is stored.

The file is typically stored on the host computer within the default Pleora directory (or
one of the subdirectories):

C:\Program Files\Common Files\Pleora

Double click on the file to launch the application.

Figure 10-6

illustrates the installation

tool dialog that is displayed.

Figure 10-6: Typical 64-Bit eBUS Driver Installation Tool Dialog

Review the list of Ethernet cards displayed. Select the desired Ethernet card, and within
the

Action

column, select

Install Manufacturer Driver

from the pull-down menu.

Click on the

Install

button to initiate the installation of the appropriate driver.

Once the driver installation has been completed, it may be necessary to reboot the
computer.

If prompted for a reboot, select:

•

Yes

to reboot the host computer immediately, or

•

to delay rebooting the computer until a later time.

When delaying the reboot, dismiss/close the

eBUS Driver Installation Tool

dialog.

Once the computer has been rebooted, verify that the network connection has been
established.

4411-0145_0046

Содержание NIRvana-LN



























































































































Результаты поиска

Содержание NIRvana-LN

Отзывы:

Princeton Instruments NIRvana-LN, Руководство пользователя, Страница: 91 / 122

Результаты поиска

Содержание NIRvana-LN

Отзывы: