background image

INSTALLATION

1.

After you have removed the toaster from the carton,
inspect the unit for signs of damage. If there is
damage to the unit:

l

Notify carrier within 24 hours after delivery.

l

Save carton and packing material for inspection
purposes.

l

Contact the Prince Castle Customer Sales
Department at 1-800-722-7853 to arrange for a
replacement to be sent.

2.

Verify that all parts have been received.

l

Slim-Line Bun Toaster and conveyor assembly.

l

Line Cord–packed separately from the toaster
and is located at the bottom of the box.

l

Release Sheets–located in a 14” box.

l

Crumb Tray–taped to the front of the conveyor.

3.

Place toaster on flat surface.

4.

Lift conveyor off conveyor guide rails and set aside.
Remove all packing materials (nylon tape, foam block
and black rubber packaging spacers) from conveyor
and conveyor guides.  See figure 1.

5.

Attach conveyor to the toaster by sliding the four pins
(conveyor slides) on the conveyor housing into the
four conveyor guides.  Lower the conveyor housing
until it is securely in place. See figure 2.

6.

Connect line cord and plug unit into a 230 volt
grounded receptacle.

OPERATION

1.

Place the release sheet over the top of the platen
housing, making sure to have three inches of over-
hang.  See figure 3.

2.

Slide the release sheet holding bracket onto the top of
the platen housing to securely hold the release sheet
in place.  Match the FRONT of the labeled bracket with
the front of the platen. See figure 3.

3.

Hook back end of crumb tray onto the bar located
below the conveyor assembly.

4.

Attach conveyor to the toaster.  See figure 2.

5.

Turn the heater switch to the “On” position.  The
orange indicator light will illuminate.  Allow 30 minutes
for platen to reach operating temperature. See figure 4.

6.

Turn the motor switch to the “On” position.  The
orange indicator light will illuminate.  See figure 4.
Conveyor chain will begin to rotate.

IMPORTANT:  To conserve energy when toaster is not in
use, turn the motor switch “Off”.

7.

Place a sample run of the product being toasted into
the top of the conveyor housing. The side to be
toasted should face the
platen. See figure 5.

8.

The toasted product
will be dispensed
automatically from the
bottom of the conveyor
assembly.  The
toasting cycle is
30-35 seconds on
model 197 and 15-18
seconds on model 297.

2

figure 3

Release
Sheet

Holding
Bracket

3-inch
Overhang

figure 5

Heel

Crown

figure 2

Conveyor
Guides

Conveyor
Guides

Heater
Switch

Motor
Switch

1

1

0

0

figure 4

Conveyor
Guides

Crumb
Tray

figure 1

Содержание Excalibur 197-FCE









Отзывы: