Primus D55 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 82

Primus D55 Скачать руководство пользователя страница 47

70276001

45

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

58. TRUNNION BEARINGS

Refer to Figure 16.
a. Remove belt guard.
b. Remove front panel assembly.
c. Place blocks under cylinder left and right of

center so that cylinder will stay level while
trunnion bearings are being replaced.

d. Remove cylinder sheave.

e. Loosen the front and rear adjusting screws.

f. Loosen setscrews holding bearings to shaft.

g. Remove bearing mounting screws.
h. Remove rear bearing.

i. Remove screws that hold mounting bracket to

tumbler.

j. Remove mounting bracket.

k. Remove front bearing mounting nuts.

l. Loosen setscrews holding bearing to shaft.

m. Remove front bearing.

Figure 16

TMB1984P

Rear

Adjusting

Screw

Mounting

Bracket

Bearing

Mounting

Screw

Rear

Bearing

Setscrews

Rear

Bearing

Assembly

Front

Bearing

Assembly

Mounting Bracket

Attaching

Screw

Front

Adjusting

Screw

Front Bearing

Setscrews

Shim

«
...
45
46
47
48
49
...
»

Содержание D55



















































































Отзывы:

Нет отзывов