FEATURES & FUNCTIONS
Front
1 Spill Proof Bottle Receptacle with Leak Guard
– For fast, easy, spill-proof
loading. Reduces leaks from worn & damaged bottles.
2 Water Dispensing Controls
– Depress to dispense.
3 Function Lights
(Not on All Models) - Green light below snowflake indicates
dispenser is cooling water. Green light below wavy lines indicates dispenser
is heating water.
4 Spout(s)
– Amount vary by model. Water dispenses here.
5 Bottle Support(s)
(Not on All Models) - Helps align sports bottles and
glasses with spout(s) to eliminate spills.
6 LED Nightlight
(Not on All Models) – Located behind bottle support(s).
Helps in low light situations.
7 Drip Tray
– Dishwasher safe. Slides in and out. Red float rises to top to
inform you it is time to empty the tray.
Back
8 Activation Switch for Cooling
– Green
9 Activation Switch for Heating
– Red (Not on All Models)
10 Activation Switch for LED Nightlight
– Blue (Not on All Models)
11 Hot Tank Drain
– Use when cleaning. Caution: Water can flow at extremely
high temperatures. Failure to use properly can cause personal injury.
11 Plug & Cord
–Only plug into a ground fault interrupting receptacle.
WARNINGS & SAFETY PRECAUTIONS
To reduce risk of injury and property damage, user must
read this entire guide before assembling, installing &
operating dispenser.
Failure to execute the instructions in this manual can
cause personal injury or property damage.
Models that heat water dispense at very high
temperatures. Failure to use properly can cause
personal injury.
When operating this dispenser, always exercise basic
safety precautions, including the following:
Prior to use, this dispenser must be properly assembled and installed in
accordance with this manual.
This dispenser is intended for water dispensing only. Do NOT use other
liquids. Do NOT use for other purposes. Never use any other liquid in the
dispenser other than known and microbiologically safe bottled water.
For indoor use only. Keep water dispenser in a dry place away from direct
sunlight. Do NOT use outdoors.
Install and use only on a hard, flat and level surface.
Do NOT place dispenser into an enclosed space or cabinet.
Do NOT operate dispenser in the presence of explosive fumes.
Position back of dispenser no closer than 4 inches from wall and permit free
airflow between wall and dispenser. There must be at least 4 inches
clearance on the sides of the dispenser to permit airflow.
The dispenser is intended to be plugged into a ground fault interrupting
receptacle.
Do not use an extension cord with your water dispenser.
Always grasp plug and pull straight out from outlet. Never unplug by pulling
on power cord.
Do NOT use dispenser if cord becomes frayed or otherwise damaged.
To protect against electric shock, do NOT immerse cord, plug, or any other
part of dispenser in water or other liquids.
Ensure dispenser is unplugged prior to cleaning.
Never allow children to dispense hot water without proper and direct
supervision. Unplug unit to prevent unsupervised use by children.
Do not dispense hot water if water bottle is empty.
Service should be performed only by a certified technician. Please contact us
at 866-429-7566 for assistance.
This Home Series water dispenser has been designed and manufactured to
provide dependable and safe service if installed, set up, operated and
maintained as directed. Follow all instructions in the order provided.
SET UP
All hardware is included. Set up requires a Phillips
screwdriver (not included).
Locate Dispenser
Notice: Do NOT plug power cord into wall outlet until instructed.
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded location near
a ground fault interrupting receptacle.
3. Position dispenser so the back is at least 4 inches from wall and there are
at least 4 inches of clearance on both sides.
Install Bracket
CAUTION: Dispenser must be securely anchored to wall as shown to
prevent accidental tip hazard.
1. Clip bracket onto back right corner of
dispenser as shown in illustration.
2. Install plastic anchor directly into sheet rock
using a Philips screwdriver. DO NOT drill
hole into sheet rock first when using this
anchor.
3. Secure by installing screw through bracket
and into the anchor.
Note: Remove screw to free dispenser for
cleaning or relocating.
Install Drip Tray & Grid
1. Remove drip tray and grid from protective packaging.
2. Slide drip tray assembly into position until it is secure.
Install Water Bottle
Bottle not included. Requires standard 3, 4 or 5 gallon water dispenser bottles.
Visit www.PrimoWater.com to find Primo Water at a store near you.
1. Remove tamper seal from top of bottle cap. Do NOT remove plastic cap.
2. Clean bottle cap and neck with a cloth and warm soapy water, then rinse.
3. Lift bottle and insert onto the probe. Apply slight pressure until the plug inside
the cap pushes in and the bottle is seated. Water will begin to flow into the
reservoirs causing air bubbles in the bottle.
Provide Electricity
Plug cord into a ground fault interrupting receptacle.
Activate Cold Switch
Notice: This unit will not dispense cold water until the switch is activated.
To activate, push top side of the green switch in to start cooling water. If you do
not want cold water leave switch in off position – bottom side pushed in.
Activate Hot Switch (Not on All Models)
Notice: This unit will not dispense hot water until the switch is activated.
To activate, push top side of the red switch in to start heating water. If you do not
want hot water leave switch in off position – bottom side pushed in.
Activate Nightlight (Not on All Models)
To activate, push top side of the blue switch in. The LED bulb behind center spout
will light. If you do not want a nightlight leave switch in off position – bottom side
pushed in.
Register at Club Primo
While you wait for the water to get to the desired temperatures, please register
your dispenser. This will be helpful should you need customer service assistance in
the future. Go to www.PrimoWater.com and click on Club Primo.
OPERATION
This Home Series water dispenser has been tested and sanitized prior to packing
and shipping. During transit dust and odors can accumulate in the tank and lines.
Dispense and dispose at least one quart of water prior to drinking any water.
Dispensing Cold Water
After setup, it will take 1 hour to get water to maximum cold temperature.
During this time the compressor will run continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control (dark blue) downward to start water flow.
3. Release control once desired fill level is achieved.
Dispensing Cool Water (Not on All Models)
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cool water control (light blue) downward to start water flow.
3. Release control once desired fill level is achieved.
Dispensing Hot Water (Not on All Models)
CAUTION: This unit dispenses water at temperatures that can cause severe
burns. Avoid direct contact with hot water. Keep children and pets away
from unit while dispensing. Never allow children to dispense hot water
without proper and direct supervision. Unplug unit to prevent unsupervised
use by children.
After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Slide red button away from you and depress control downward to
start water flow.
3. Release control once desired fill level is achieved.
MAINTENANCE
For best taste, performance and hygiene, clean the cold tank at least every 3
months and your cabinet, controls and spout each time you change your water
bottle.. Empty and clean drip tray as needed. To minimize mineral deposits, use
only high quality purified bottled water such as Primo.
For instructions and videos for maintaining your dispenser please visit -
http://store.primowater.com/SpecialPages/CustomerCare.aspx#
LIMITED WARRANTY
Primo Water Corporation, (“Vendor”) warrants to the original purchaser of this
dispenser, and to no other person, that if this dispenser is assembled and
operated in accordance with the printed instructions accompanying it, then for
a period of one (1) year from the date of purchase, all parts in such dispenser
shall be free from defects in material and workmanship. Vendor may require
reasonable proof of your date of purchase from an authorized retailer or
distributor. Therefore, you should retain your sales slip or invoice. The Limited
Warranty shall be limited to repair or replacement of parts, which prove
defective under normal use and service and which Vendor shall determine in
its reasonable discretion upon examination to be defective. Before returning
any parts, you should contact Vendor’s Customer Care Department using the
contact information listed below. If Vendor confirms, after examination, a
defect covered by this Limited Warranty in any returned part, and if Vendor
approves claim, Vendor will replace such defective part without charge. If you
return defective parts, transportation charges must be prepaid by you. Vendor
will return replacement parts to original purchaser, freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties due
to accident, abuse, misuse, alteration, misapplication, improper installation or
improper maintenance or service by you or any third party, or failure to
perform normal and routine maintenance on the dispenser, as set out in the
User’s Manual. In addition, the Limited Warranty does not cover damages to
the finish, such as scratches, dents, discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor
disclaims all warranties for products that are purchased from seller other than
authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR
EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER,
VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR
CONSEQUENTAL DAMAGES. Vendor assumes no responsibility for any defects
caused by third parties. This Limited Warranty gives the purchaser specific
legal rights; a purchaser may have other rights depending upon where he or
she lives. Some jurisdictions do not allow exclusion or limitation of special,
incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to you.
Primo Water Corporation
104 Cambridge Plaza Drive, Winston-Salem, NC 27104
www.PrimoWater.com
Home Series
Spill Proof
Water Dispensers
TO REDUCE THE RISK OF INJURY
AND PROPERTY DAMAGE, USER
MUST READ THIS MANUAL
BEFORE ASSEMBLING, INSTALLING
& OPERATING DISPENSER.
SAVE THIS MANUAL
FOR FUTURE USE
Water is leaking.
Bottle may have a leak that is too large for the Leak Guard feature to stop.
Remove bottle, dispense one quart of water and install new bottle.
If leak remains, remove bottle and call 866-429-7566 for assistance.
No water is coming from the spout.
Make sure the bottle is not empty. If empty, replace it.
Make sure to push the water controls in fully.
Cold water is not cold.
It takes up to one hour after setup to dispense cold water.
Make sure the power cord is properly connected to a working outlet.
Make sure the back of the dispenser is at least 4 inches from a wall and
there is free airflow on all 4 sides of the dispenser.
Make sure green switch on back of dispenser is ON.
If water still isn’t cold, please call 866-429-7566 for assistance.
Hot water is not hot. (Not on All Models)
It takes 15-20 minutes after setup to dispense hot water.
Make sure the power cord is properly connected to a working outlet.
Make sure red switch on back of dispenser is ON.
Nightlight Isn’t Working (Not on All Models)
Make sure the power cord is properly connected to a working outlet.
Make sure nightlight switch on back of dispenser is ON.
Dispenser Is Noisy
Make sure the dispenser is positioned on a level surface.
TROUBLESHOOTING
Join Club Primo at PrimoWater.com for more useful information, instructional videos, tips and special offers.
IMPORTANT: Do Not Return Dispenser to Store. If you have questions or issues please contact 1-866-429-7566 for expert assistance.
PN O-075 © 2012 Primo Water Corporation
1
3
4
7
2
5
6
12
11
8
10
9
