Prime Tech H-066, Руководство пользователя

Страница: 6 / 6

1. The car must be in power-off, when installing ultrasonic sensors
2. Its performance may be affected in following situation: heavy rain, gravel road, bumpy
road sloping road and bush, very cold, hot or moist weather, or the sensors is firned or
iced over.
3. Switches among ultrasonic, electric wave, DC and AC and those among 24V, 12V
voltages may also effects its performance.
4. The sensors should be installed appropriate loose or tight.
5. Its performance will be effected if the sensors are fixed on metallic bumper.
6. Avoid installing the digital control box in places of great interference, such as vent-pipe,
wiring nearby.
7. Test the system to make sure it works normally before using.
8. This system is a reversing aid and the manufacturer will take no responsibility for any
accidents caused after the kit is installed.
H-066 Parking Sensor System consists of ultrasonic sensors, digital control box and LCD
display. The system detects the distance between the car and front/rear obstruction by
ultrasonic sensors installed at the front/rear bumper of car. The distance will be displayed
in an innovative mode with the special designed LCD, numeric display and step-up sounds,
which will be changed according to the actual positions detected obstruction so that the
driver could judge the distance and avoid accident.
1. Choose right installation position for sensors
2. Select drilling position for sensor A & D
Select drilling position for sensor 1 & 4
3. Select drilling position for sensor B & C Select drilling position for sensor 2 & 3
4. Locate the position and drill
5. Install the sensors and hide wires
6. Install the display
7. Install the control box
8. Connect the whole system according to the General Installation Diagram
NOTE
INSTALLATION AND TEST
INSTALLATION STEPS
ALARM MODE
TECHNICAL SPECIFICATIONS
MAIN FEATURES
0.3m
1
2
3
4 0.3
1.5~1.1m
1.0~0.4m
1.5~1.1
1.0~0.4
( Rear detection )
1. Adjust the directions of the sensors and axial orientation, neaten the wiring after installing
the sensors.
2. Connect the power supply of back control box to the reversing light. Connect the power
supply of front control box to auto ignition switch.
3. Connect the data wires between the front control box and display, and disposal the
control switch with front control box. Do not disposal the sensor at the moment.
4. When the car is started, the horn sounds "Dang,Dang" to enter into working status , 2s
later, it turns to standby status. Put the car into back gear, then the display shows "En"
(n=0,1,2
)to show the number of defective sensors, with the indication of exact
defective sensors. Insert one of the sensors into corresponding interface in front/back
control box. Human being could be detected normally, if he stands within 0.7m right
before the sensor; Pull out the sensor, and check other sensors in the same method.
Insert all the sensors in corresponding interfaces after testing.
Test: a. After connect a sensor with the control box, if the buzzer sounds"Bi ", please
check whether there is any obstacle around it, or the sensor is fixed too tight or close to
great interference sources(such as vent-pipe, wires) ;b. If the display shows any distance
figure with no obstacle around the sensor, the sensor may detect the ground or some
outshoots of the car(such as registration mark etc.), please check the directions of sensor
and axes; c. If the system still could not work properly after the above mentioned handling,
the sensor(s ) can be deemed defective, or unmatch with the control box. The system
should be replaced.
Note: a. The connection between sensor and the digital control box is unique. b. It performs
as: when detecting within 0.3m, it shows "0.0", instead of 0.1-0.2 to alert which requires
the driver to stop immediately.
Dang Dang
Dang Dang Dang
Dang
>1.5m
5 <0.3m 0.0 Dang
H-066
Rated Voltage: DC 12V
Operating Range: DC 10-16V
Operating Current: 30-360mA
Detecting Distance: Front
0.3 0.7m Rear 0.3 1.5m
Ultrasonic Frequency: 40KHz
Working Temperature of Control Box: -30-+70
Working Temperature of Display: -20-+70
Display Size: 70*32*14mm
Stage Distance Awareness Alarm Color Alarm Sound Digital Display
White
White
White
White
Danger Area
Alarm Area
Safety Area
Danger Area
Safety Area
Digital LCD display
Three-stage simulation alarm
Front and back detection
Four-stage simulation distance display
"DingDingDing", "DangDangDang" alarm sound
Hidden installation
Switch, Braking delay control
Self-test function of sensor
0.6~0.7m
0.4~0.5m
0.3m 0.3
0.6~0.7
Silence
Silence
Ding Ding Ding
Ding
>0.7m
0.4~0.5
<0.3m 0.0 Ding
Ding Ding Ding
1
2
3
4
( Front detection )
5
Stage Distance Awareness Alarm Color Alarm Sound Digital Display
White
White
White
White
Danger Area
Alarm Area
Safety Area
Danger Area
Safety Area