Pride Quantum 614 Скачать руководство пользователя

Страница: 30 / 44

30 www.pridemobility.com Quantum 614 Series

V I . B A T T E R I E S A N D C H A R G I N G

Battery Break-in

To break in new batteries for maximum efficiency:

1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak

performance level.

2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until

you become accustomed to the controls and break in the batteries.

3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will

now perform at over 90% of their potential.

4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.

Frequently Asked Questions (FAQs)

How does the charger work?

The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it

to 24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery

voltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the

charger does not work as hard to complete the charging cycle. When the battery is fully charged, the amperage

from the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.

Can I use a different battery charger

You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries.

We do not recommend using other types of chargers (e.g., an automotive battery charger).

NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero

voltage. If this happens, call your Quantum Rehab Provider for assistance.

Figure 20. Battery Charging

To charge the batteries using the off-board charger:

1. Position the front of your power chair next to a

standard electrical outlet.

2. Be certain the controller power is turned off.

3. Plug the off-board charger into the off-board char-

ger/programming socket on the controller. See

figure 20.

4. Plug the off-board charger into the electrical outlet.

NOTE: The LED lights on the charger indicate dif-

ferent charger conditions at various times: charger

power on, charging in progress, and charging com-

plete. Refer to the manual supplied with the charger

for a complete explanation of these indicators.

5. When the batteries are fully charged, unplug the

off-board charger from the electrical outlet and

then from the controller.

Содержание Quantum 614













































Результаты поиска

Содержание Quantum 614

Отзывы:

Похожие инструкции для Quantum 614

Бренды по названию

Популярные бренды

Pride Quantum 614, Руководство пользователя

Результаты поиска

Содержание Quantum 614

Отзывы:

Похожие инструкции для Quantum 614

Бренды по названию

Популярные бренды