background image

3

www.pridemobility.com

   INFINFB2048/Rev A/11-29-06

B

ASIC

 T

ROUBLESHOOTING

 I

NSTRUCTIONS

: J

AZZY

 S

ELECT

 14

What if the speed LEDs on the VSI begin to flash?

!

Determine if the battery charger is connected to the power base. When the battery charger is connected to
the power base, an internal charger inhibit feature keeps the power chair from driving. This is indicated by the
VSI speed LED(s) flashing.

!

Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
activate.

!

Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

What if the speed LEDs on the VSI begin to scroll?

!

Determine if the VSI has been placed in lock mode. The VSI is equipped with a lock mode feature that
prevents unintended use of the power chair. If the VSI is in lock mode, deflect the joystick full forward until it
beeps, and then deflect the joystick full rearward until it beeps. The controller should go back to the drive
function.

VR2 DIAGNOSTIC FAULT CODES

  FAULT CODE PROBABLE CAUSE(S)

POSSIBLE SOLUTION

  One red LED

The batteries need charging.

Check the battery connections. If the battery

There is a bad connection to the batteries.

connections are good, then try charging the
batteries.

  Two red LEDs

There is a bad connection on the left motor. Check the left motor connections and wiring

harnesses.

  Three red LEDs

The left motor has a short to a battery

Contact your authorized Pride Provider.

connection.

  Three red LEDs

There is a bad connection on the right

Check the right motor connections and wiring

  One yellow LED

motor.

harnesses.

  Three red LEDs

The right motor has a short to a battery

Contact your authorized Pride Provider.

  Two yellow LEDs

connection.

  Three red LEDs

The charge inhibit has been activated.

Make sure that the battery charger is not

  Three yellow LEDs

connected to the power base.

  Three red LEDs

There is a joystick fault.

Make sure the joystick is in the center position

  Four yellow LEDs

and then power off and on again.

  Three red LEDs

There is a control system fault.

Check power module and joystick module

  Four yellow LEDs

connections and wiring.

  One green LED
  Three red LEDs

The park brakes have a bad connection.

Check the left and right motor connections and

  Four yellow LEDs

wiring.

  Two green LEDs
  Three red LEDs

An excessive voltage has been applied to

Check the battery connections.

  Four yellow LEDs

the control system.

  Three green LEDs

What if the left red battery condition meter LED on the VR2 is flashing?

!

This indicates that battery voltage is very low and the batteiries should be charged immediately.

Содержание Jazzy Select 14 INFINFB2048

Страница 1: ... a week for 12 14 hours Determine how long you let the batteries charge It takes 8 14 hours to fully charge a depleted set of batteries continual undercharging reduces the overall life of the batteries Observe the ammeter during battery charging to determine if the batteries are receiving a charge If the ammeter does not go up when the battery charger is plugged into the charger power cord recepta...

Страница 2: ...will not spin the wheels Determine if the controller is flashing a fault code The Jazzy Select 14 comes equipped with a VSI or VR2 controller Both controllers will flash a code via the battery condition meter LEDs if a system fault is detected VSI DIAGNOSTIC FLASH CODES OF LEDS CODE CAUSE POSSIBLE SOLUTION One red LED 1 Low battery voltage Charge batteries Two red LEDs 2 Left motor open Make sure ...

Страница 3: ...ry There is a bad connection to the batteries connections are good then try charging the batteries Two red LEDs There is a bad connection on the left motor Check the left motor connections and wiring harnesses Three red LEDs The left motor has a short to a battery Contact your authorized Pride Provider connection Three red LEDs There is a bad connection on the right Check the right motor connectio...

Страница 4: ... an internal charger inhibit feature keeps the power chair from driving Determine if the charger harness fuse has blown A blown charger fuse can cause the charger inhibit to activate What if all of the battery condition meter LEDs on the VR2 blink once every 2 5 seconds This indicates that the VR2 is in sleep mode Turn the controller off then back on to resume normal operation INFINFB2048 Rev A 11...

Отзывы: