32
Copyright © 2004 CBTricks.com
Pride DX-300
CHAPTER 2
Figure 2-1 Front Panel
2.1
OPERATION:
1)
Check to see that the
TUNE/STANDBY/OPERATE
switch is in the center or
STANDBY
position. Apply power
to the unit by switching the
POWER
switch to the
ON
position. You will hear the cooling blower come up to
speed. Wait 60 seconds for the tube to come up to operating temperature.
2)
During the time that the amplifier is warming up or at any time that the
TUNE/STANDBY/OPERATE
switch is
in the
STANDBY
position, the exciter may be operated normally "straight through" the amplifier.
3)
Set the band switch to the same band as that the exciter is tuned to.
4)
After warm up, place the
TUNE/STANDBY/OPERATE
switch into the
TUNE
position. The
OPERATE
indicator will light up, indicating that the unit is ready for operation. If the
RECEIVE
switch is on, the
RECEIVE
indicator will light also, indicating operation of the receive preamplifier.
5)
Rotate the
PLATE LOADING
control to the nine o'clock (counter clockwise) position.
6)
Apply several watts of drive from the exciter and quickly peak the
PLATE TUNE
control for maximum output
as indicated on the front panel wattmeter. The
SCREEN
overload indicator may glow at this time, and will peak
in brilliance at approximately the same place of tuning that maximum output occurs.
7)
The
PLATE LOADING
control is then turned clockwise 1/2 division or so, and the
PLATE TUNING
control is
peaked again for maximum output. The brilliance of the
SCREEN
indicator will peak again, but not quite as
brightly as before. This process is continued until a further increase in the
PLATE LOADING
control will give no
further increase in power output. This will normally result in approximately 100watts output for three to four watts
of driving power.
8)
Un-key the exciter, and place the
TUNE/STANDBY/OPERATE
switch in the
OPERATE
position. When the
exciter is keyed again, the power output will be somewhat higher, and the
SCREEN
indicator may glow brightly
again. Repeat the procedure as before, tuning the
PLATE LOADING
and
PLATE TUNING
controls alternately
for maximum output. The
PLATE TUNING
control should always be the last control that is adjusted. Power
output should be about 250watts for five watts drive at this point in the tune up procedure. When proper loading
is accomplished, the
SCREEN
indicator should glow only dimly. The plate current, as read on an external meter,
should be in the neighborhood of 200-250ma.
Содержание Amp Series
