background image

www.pridemobility.com 

Jazzy EVO 614 Series

I I I .   Y O U R   P O W E R   C H A I R

1

7

3

4

2

6

5

Figure 2. The Jazzy EVO 614 Series

 

Power Base

Electrical components

The electrical components are located on or inside the power base. The main circuit breaker is located on the front 

of the power base. The power module is located inside the power base. 

See figure 3. 

Motor Connectors: 

This is where the power module connects to the motors.

Battery Connector: 

This is where the power module connects to the batteries.

Controller Connector:

 This is where the controller connects to the power module or power base. Each controller 

uses a different type of harness. Regardless of which type of controller is used, the harness must be secured to the 

seat assembly and not allowed to drag on the floor.

Power Module:

 Provides connection between the joystick module and the motors, batteries, and off-board charger

1.  Seat Post

2.  Rear Shroud

3.  Top Shroud

4.  Front Caster Wheels

5.  Main Circuit Breaker

6.  Rear Caster Wheel

7.  Controller Connector

Identification Key

Содержание Jazzy EVO 614 HD

































Отзывы: