background image

128-9364

25 of 28

25

PROGRAMMING BANK 3

 (REMOTE START ):

You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made the changes 

you wanted in Bank 2, (Siren Chirps 3 times), you can also go right to bank 3 by:

1) Turn the ignition key to the on position.

2) Press and release the valet/programming switch 3 times (Siren Chirps Once).

3) Turn the ignition key off then on. (Siren Chirps 2 Times)

4) Turn the ignition key off then on. (Siren Chirps 3 Times)

 

5) Press the push button switch once to advance to feature 1, twice to advance to feature 2, etc,,,then 

use the lock button of the transmitter to select the feature setting.

Example to set engine input check to DBI Tach:

1) Turn the ignition key to the on position.

2) Press and release the valet/programming switch 3 times (Siren Chirps Once) 

3) Turn the ignition key off, then on. (2 Chirps)

4) Turn the ignition key off then on. (3 Chirps)

 

5) Press the push button switch five times to advance to features 5, Input Check, then use the lock button 

of the transmitter to select three chirps, "DBI Tach"

6) To exit the programming mode, turn the ignition key off more than 6 seconds.   Siren sounds a short 

chirp followed by a long Chirp.

TACH RATE PROGRAMMING:

1. Turn the ignition key to the On position.

2. Press and release the valet/program push button switch 3 times.

3. Immediately turn the ignition key Off.

4. Press and hold the valet/program push button switch, then start the vehicle using the key.

5. When the unit senses the tach signal, the parking lights will begin to flash.

6. Release the valet/program pushbutton switch.  The parking lights will turn on for three seconds to 

indicate that the learned tach signal is stored and the unit is out of the tach learn mode.

NOTE:

  If the unit fails to learn tach rate due to an improper tachometer connection or a poor tach source, 

the parking lights will not flash.  To correct this situation, locate and connect the Green/Orange 

wire to the proper tach signal, and then repeat the tach learn routine.

Содержание APS-922E





























Отзывы: