background image

128-7132

1 of 8

Model APS-596

Installation Manual

Note:

 The method of manual override can either be selected to operate from the valet switch or operate as custom

code.  Be certain to place a check mark indicating the method used in the box located on the last page of the
owner's manual.

Note:

 When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin

switch in order to begin the passive arming sequence.

RF Programmable Features :

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

Default

1st Door L/UL

1 Sec.

3.5 Sec.

1 Sec L, Dbl. U/L

1 Sec.

2nd Accy Lock

Auto Lock On

Auto Lock Off

Auto Lock Off

3rd Accy. UL

Auto UL Dr

Auto UL All

Auto UL Off

Auto UL Off

4th Headlights

On Arm

On Disarm

On Both

Off

Both

5th Passive Locks

Passive

Active

Active

6th Passive/Active Arm

Passive  Arm

Active Arm

Active Arm

7th Voltage Sense

Voltage Sense

Hardwire

Hardwire

8th Siren/Horn

Siren/Horn

Siren Only

Horn Only

Siren/Horn

9th Horn Chirp

10mS

16mS

30mS

16mS

10th Override Method

Custom Code

Valet

Valet

11th Two Step Unlock

On

Off

Off

12th Chirp Delete From Tx On

Off

Off

To program these selectable features;

Action

System Response

Turn ignition on

No response

Press and release the valet switch 3 times

1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off

Short chirp, then long chirp

First

Then On

1 chirp = 1 second door locks

Press transmitter Lock button to change

2 chirps = 3.5 second door locks

Press transmitter Lock button to change

3 chirps = 1 sec. lock, dbl 1 sec. unlock

or

Second Press and release the valet switch

2 chirps = auto locks off

Press transmitter Lock button to change

1 chirp = auto locks on

or

Third

Press and release the valet switch

3 chirps = auto unlock off

Press transmitter Lock button to change

1 chirp = auto unlock drivers door only

Press transmitter Lock button to change

2 chirps = auto unlock all doors

or

Fourth

Press  and release the valet switch

3 chirps = headlight output when arming and disarming

Press transmitter Lock button to change

4 chirps = headlight output off

Press transmitter Lock button to change

1 chirp = headlight output when arming

Press transmitter Lock button to change

2 chirps = headlight output when disarming

or

Содержание 1287132









Отзывы: