35
CB is a “simplex” communication mode, it is not possible to speak
and listen at the same time (as it is the case with a telephone).
Once the conversation was over, he said “Roger” in order to
prevent his correspondent that it was his turn to talk. The word
“Roger” has been replaced by a significant beep. That is where
the name “Roger beep” comes from.
-
Turn on the power while pressing the
s
key (
3a
) or
UP
knob (
12
)
to alternate between enable (
On
) or disable (
OF
) the
ROGER BEEP
function.
- When function is activated,
“ ”
appears on the display.
Note:
The Roger beep also sounds in the loudspeaker if the
KEY
BEEP
function is active. If the
KEY BEEP
function is not active, only
the correspondent can hear the
ROGER BEEP
.
In
PA
mode the function is not allowed.
2) KEY BEEP
(
t
key on the unit or
DN
knob on microphone)
Some operations such as changing channels, pressure on keys etc.
are confirmed by a beep tone. This beep tone can be activated
or deactivated as follows:
-
Turn on the power while pressing the
t
key (
3b
) or the
DN
knob
(
12
) to alternate between enable (
On
) or disable (
OF
) the
KEY BEEP
function.
- When function is activated,
“BP”
appears on the display.
3) F - FREQUENCY BAND SELECTION
(
F
key)
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country
of use. Don’t use any other configuration. Some countries need a
user’s licence.
See table page 68.
Proceeding:
-
Turn on the power while pressing the
F
key (
5
).
The symbol corresponding to the current configuration is blinking.
-
In order to change the configuration, use the
s
/
t
keys (
3
) on the
unit or the
UP
/
DN
knobs (
12
) on the microphone.
- When the configuration is selected, press the
F
key (
5
) during 1
second. The symbol corresponding to the configuration is contin-
uously displayed and a confirmation tone beep sounds.
-
At this point, confirm the selection by switching off the transceiver
and then switching it on again.
See the configurations/frequency bands table at pages 64 to 66.
4) COLOR
(
MODE
+
EMG
keys)
- Turn on the power while pressing the
MODE
(
6
) and
EMG
(
7
) keys.
The symbol of the current color, among the seven, blinks: (or-
ange), (green), (blue), (cyan), (yellow), (purple) or
(cyan light).
- Use the
s
/
t
keys (
3
) on the unit or
UP
/
DN
knobs (
12
) on the mi-
crophone to change the color.
- When the color is set, long press the
F
key (
5
). A beep sounds, the
characters of the color are displayed during 1 second.
5) RESET
- Turn on the power while pressing the
EMG
key (
7
) to reset to the
factory settings.
- “
rS
” blinks in the display.
- Press the
F
key (
5
) for 1 second to confirm.
D) FUNCTIONS WITH PTT SWITCH
4 more functions are available. To activate the function press and
hold the
PTT
switch (
11
) and press the function key. Repeat this
process to deactivate the function.
1) TALKBACK
(
PTT
+
F
)
The
TALKBACK
function
can be activated or deactivated as follows:
a)
Press and hold the
PTT
switch (
11
)
b)
Short press on
F
key (
5
). Current
TALKBACK
level blinks 3 times
allowing you to adjust this level.
When function is activated,
“TALKBACK”
appears on the display.
This function allows to ear your own modulation with the CB speaker.
English
Содержание BARRY II
