Premium PWC225Q, Инструкция по использованию и уходу

Страница: 4 / 5

Major technical parameters of water dispenser
Power source 110~60Hz
Temperature
10 ~
℃ ℃
38
Relative humidity 45%~75% Elevation ability
It's plateau machine
if elevation
surpasses 1000M.
Heating power
500W
Capacity of
making hot water
5L/h( 90 )
≥ ℃
Cooling power
Electronic cooling 65W
Compressor cooling 85W
Refrigerator cooling 100W
Capacity of
making cold water
Electronic cooling
0.5~0.8L/h(
15 )
Compressor cooling
2L/h(
10 )
≤
≤
℃
℃
Operating
environment
No combustible, explosive and corrosive gas and electric conduction dust and no
strenuous vibration etc. in ambient air (the ambient temperature of electronic
cooling machine is
32 . If ambient temperature is <15 , please close cooling
system to avoid the engine body from freezing and freezing off its pipeline.
≤ ℃ ℃
List for maintenance measures of water dispenser's common faults
Fault
phenomenon
Possible cause Solution
Fail to heat
1 don't turn on heat switch
）
2 avoid burning temperature controller
）
3 heat temperature controller is damaged
）
4 the electrical heated tube inside hot
pot is damaged
）
5 power line is damaged
）
Turn on switch
Hand reset
Replace a new temperature
controller
Replace a new hot pot
Replace a new power line
Fail to cool
1 don't turn on cool switch
）
2 cool temperature controller is damaged
）
3 compressor is damaged
）
4 leak coolants
）
5 impurities and ice block dry filtering
tube or capillary
）
6 the vacuum of compressor is not
high enough, making cooling effect bad
）
rush vacuum and fill coolants
again
Let out coolants, fill nitrogen
to clean, and rush vacuum
and fill coolants again
Weld again
Replace a new compressor
Replace a new temperature
controller
Turn on switch
Doesn't halt while
heating and cooling
1 temperature controller is damaged
）
2 leak coolants freezing medium
） （ ）
3 ambient temperature is too high, cooling
doesn't halt.
）
Improve temperature
environment, or stop
using cooling function
temporarily.
Weld the part leaking
fluorine, replenish coolants
Replace a new temperature
controller
Don't effluent
7 ice block
）
6 foreign body inside the tube
）
5 heat temperature is over high, making pot
full of gas. Water can't flow out of faucet.
）
4 the air inside hot tank is not evacuated.
）
3 the tube where connects to faucet ties off.
）
2 there's foam at the point where water
tank and water dispenser connect.
）
1 pressure inside water tank is lower than
that of outside
） Take down water bottle
and fix again
Pat the body till water
flows out
Fix silicone tube again.
Pat the body till water
flows out
Break heat switch
temporarily.
Check and remove
foreign body
Close cooling system
for 4 hours.
Leak
1 heating temperature inside hot pot is over
high, making connecting tube expanding and
water leak from connection point.
）
2 the ribbon is not locked tightly
）
3 the dimensions of tube don't match well,
causing leaking water.
）
4 seal ring is damaged
）
5 bucket bursts
）
Stop heating and check
Lock tightly again
Replace silicone tube
Replace seal ring
Replace bucket
Common fault and cause of computer display board
Water temperature
is not enough
1 use too much hot water within short period
）
2 use too much cold water within short period
）
3 heat temperature controller is aged
）
4 adjust pressure temperature controller
imprecisely
）
Replace by professional
Replace heat temperature
controller
Take water after a while
Take water after a while
Series No
Fault phenomenon
Fault cause
1
2
3
Other fault: please check whether line falls off or not. If it's good, replace element.
Cold water temperature
shows “E2”, buzzer alarms
H o t w a t e r t e m p e r a t u r e
shows “E3”, buzzer alarms
H o t w a t e r t e m p e r a t u r e
shows “E1”,buzzer alarms
Hot water temperature sensor doesn't connect or
short circuit (or open circuit) occurs.
Please connect well or replace temperature sensor.
The heating temperature of hot pot exceeds appointed
temperature
98
（ ） ℃
Cold water temperature sensor doesn't connect or
short circuit (or open circuit) occurs.
Please connect well or replace temperature
sensor.