background image

8

REPLACING THE BULB 

Unplug the AC power cord from the wall.

Remove the screw that holds the light bulb cover.

Remove the light bulb cover.

Unscrew the bulb.

Replace with a 10 watt bulb that is the same shape and size.

Replace the light bulb cover

TROUBLESHOOTING

 

GUIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

   

 

 

   

   

 

 

 

   

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The temperature of freezer and refrigerator 

PROBLEM

POSSIBLE CAUSE

Fan no work

No defrost.Freezer room temperature 

no enough cold and refrigerator room 

OK and open the cover board of are 

duct and find ice formation on evaporator

are no enough cold and the temperature no 

change by adjusting the potentiometer 

(thermostat) 

Compressor no starting

Compressor no starting

Product no any work

The drainpipe contain impurity

The sensor failure or PCB failure

The defrost heater is break or PCB failure

The potentiometer failure

The sensor failure

No problem

PCB failure

Compressor wire not right or compressor damage

The PCB failure

The fan motor fails;
Replace it with a new one






Содержание PRN7005HW










Отзывы: