Premier Mounts PSM-402F Скачать руководство пользователя страница 3

 

3

 
 
      

 

 

 
 
 
 
 

 

   

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

The wall or ceiling structure must be capable of supporting at least five (5) times the weight of plasma display. 

If not, the wall or ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions 

must be adhered to. Failure to do so could result in serious personal injury

 

The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before 

beginning installation.  The installation instructions should be read, understood and followed to prevent personal injury or property damage. 

Keep these installation instructions in an easily accessible location for future reference. 

Indicates that the power plug is to be disconnected from 

the power outlet. 

Safety precautions must be taken at all times. 

Contact Premier Mounts for any questions 

Warning and caution in general 

A secured structure wooden stud wall must always support the weight or load of the plasma.  Always confirm the center of the wood 
stud before beginning the installation.  

Do not install in locations where there is vibration, movement or danger of impact.  Failure to do so could result in plasma cracking or 
falling from the wall causing damage and injury.  

Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy.  Failure to do so may 
result in damage to the plasma television and could cause a risk of fire.  

At least two qualified people should always perform the installation work.  Injury and damage can result from dropping or mishandling 
the plasma television.  

Mounting structure recommended wood studs, solid-flat concrete, and reinforced metal studs. If installing the mount on other than 
wood studs use (commercially available) suitable hardware.  

Safety & Precautions  

WARNING

: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the 

installations procedure to prevent personal injury or damage to the plasma displays or plasma mounts. 

Содержание PSM-402F











Отзывы: