background image

Page 16

For technical questions, please call 1-888-866-5797.

ITEM 63404

        

SAFETY

OpERA

TION

MAINTENANCE

SETUp

After Each Use

1.  Remove drain plug from front of Pump.

Drain plug

2.  Tilt Pump forward to drain all 

remaining water from inside.

 Long Term Storage

When the equipment is to remain idle for longer than 
20 days, prepare the engine for storage as follows:
1. 

CLEANING

:

Wait for engine to cool, then clean engine with 
dry cloth.  

NOTICE:

  

Do not clean using water.

  

The water will gradually enter the engine 
and cause rust damage.  Apply a thin coat 
of rust preventive oil to all metal parts.

2. 

FUEL:

To protect the fuel tank during storage, fill the 
tank with gasoline that has been treated with 
a fuel stabilizer additive.  Follow fuel stabilizer 
manufacturer’s recommendations for use.  Refer 
to 

Checking and Filling Fuel

 on page 14.

WARNING! TO pREVENT SERIOUS 

INJURY FROM FIRE:

Fill tank in a well-ventilated area away from 
ignition sources.  If the engine is hot from 
use, shut the engine off and wait for it to 
cool before adding fuel.  Do not smoke.  

3. 

LUBRICATION:

a.  Change engine oil.
b.  Clean out area around spark plug.  Remove 

spark plug and pour one tablespoon of engine 
oil into cylinder through spark plug hole.

c.  Replace spark plug, but leave 

spark plug cap disconnected.

d.  Pull Starter Handle to distribute oil in cylinder.  

Stop after one or two revolutions when you 
feel the piston start the compression stroke 
(when you start to feel resistance).

4. 

BATTERY:

Disconnect battery cables (if equipped).
Recharge batteries monthly while in storage.

5. 

STORAGE AREA:

Cover and store in a dry, level, well-ventilated 
area out of reach of children.  Storage area 
should also be away from ignition sources, such 
as water heaters, clothes dryers, and furnaces.

NOTICE:

 For every 3 months of an extended 

storage period, the pump must be connected to a 
water supply, primed, started, and allowed to run 

for 15 – 20 minutes or the Warranty is VOID.

6. 

AFTER STORAGE:

Before starting the engine after storage, keep in 
mind that untreated gasoline will deteriorate quickly.  
Drain the fuel tank and change to fresh fuel if 
untreated gasoline has been sitting for a month, 
if treated gasoline has been sitting beyond 
the fuel stabilizer’s recommended time 
period, or if the engine does not start.

Содержание 63404

























Отзывы: