Precor CW-113 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 44

background image

CW-113 Assembly and Maintenance Guide

page 9

Assemble the Unit, continued

5. Pull on the Adjustment Pin and slide the Back

Adjustment through the Main Frame. Release the
Adjustment Pin while it is aligned with the Back
Adjustment middle hole.

Note:

Make sure the Springs slide onto the posts

on the bottom of the Back Support

6. Slide the Sleeve through the Back Support. Align

the holes and attach the Back Support to the Main
Frame using
one 5¼-inch buttonhead screw (E)
two ½-inch washers (F)
one ½-inch locknut (G)
Wrench tighten using a ¾-inch open end wrench.

7. Attach the Holder Assembly to the Back Support

using
four ¾-inch buttonhead screws (A)
four

³⁄₈

-inch split washers (B)

Wrench tighten.

4 - ¾” buttonhead screws

4 - split washers

1 - 5¼” buttonhead screw

1 - sleeve

2 - washers

1 - locknut

Sleeve

«
...
7
8
9
10
11
...
»

Содержание CW-113













































Отзывы:

Нет отзывов

Похожие инструкции для CW-113

Бренд: Canta Страницы: 2

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Eagle Страницы: 3

Бренд: UNIA Страницы: 62

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Waters Страницы: 250

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды