background image

9.17, 917si Treadmill

Page 1

9.17, 9.17si Treadmill

Warning:

 This service manual is for use by Precor trained service providers only.

If you are not a Precor Trained Servicer, you must not attempt to service any Precor Product;               

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and 
replacement procedures required to repair and maintain this product. 

This document contains general product information, software diagnostic procedures (when 
available), preventative maintenance procedures, inspection and adjustment procedures, 
troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the 
left of this page. You may “drag” the separator bar between this page and the bookmark section 
to change the size of the page being viewed.

                                                                 © 2003 Precor Incorporated
                                   Unauthorized Reproduction and Distribution Prohibited By Law

.

Содержание 9.17













































Отзывы: