To complete the seat assembly:
1. Connect the heart rate sensor cable in the handlebars to the cable you fed through the
seat back in the previous procedure. Feed any extra cable back into the seat back
assembly.
2. Tilt the handlebar assembly with the handlebars slightly downward before fitting it into
the slot behind the seat, making sure not to pinch the cable (Figure 7). Roll the
handlebar assembly upward so that it seats in the slot behind the seat.
3. Secure the handlebars using two M10 x 55 mm BHSC and two M10 hex nuts (Figure 8).
IMPORTANT
Gently move the cable out of the way of the screw hole. If necessary, use a dull-
edged tool inserted through the hole on the back of the handlebar assembly to
move the cable.
4. Fully tighten using a 6 mm hex wrench and a 14 mm open-end box or socket wrench.
Figure 7
Figure 8
To attach the bottle holder:
1. Move the seat back as far as it can go beyond the last latch and have your assistant hold
it in place.
2. Position the bottle holder so that the two tabs on its underside are aligned with the
bottle holder bracket.
3. Slide the bottle holder forward so that its tabs fit around the bracket (Figure 9) and the
screw hole in the center of the bottle holder and the bracket line up .
4. Secure it using an M5 x 16 mm BHCS and a 5 mm flat washer (Figure 10). Fully tighten
using a short 3 mm ball end hex wrench.
Figure 9
Figure 10
Attach the upright support and cables
CAUTION
DO NOT attempt to connect electrical power until all assembly procedures are complete
and properly installed.
Figure 11
To attach the upright support and cables:
1. Retrieve the cables for the console that you plan to install on this bike and for any PVS equipment that
you plan to install on the console.
2. Remove the wire tie holding the base unit data cable in place inside the upright support channel. Save
the tie for use in Step 4.
If you are installing PVS equipment on the console, continue with Step 3. If you are not installing PVS
equipment, skip to Step 5.
3. Use the wire tie from Step 1 to bind the upper ends of the cables together.
4. Feed the television and power cables through the opening at the bottom of the front stabilizer.
5. Using a fish tape, place the upright support on the floor with its lower end next to the bike. Thread the
cable(s) upward through the support and secure them to the top of the support.
6. Remove the extra serial number label from the upright support channel and set it aside for attachment
to the console mount bracket during console installation.
7. Lift the upright support and position its lower end over the upright support channel. Set the upright
support so that it rests on the metal tab within the upright support channel to prevent sliding (Figure
11).
IMPORTANT
In the following step, be extremely careful not to trap or pinch any of the cables between the
mounting screws and their seats.
8. Insert two M12 x 80 mm SHCS through the opening on the support and into the holes on the body
assembly (Figure 12). Fully tighten using a 10 mm hex wrench.
Figure 12
Level the equipment
Make sure the equipment is level before allowing anyone to use it.
CAUTION
To eliminate movement, make sure the adjustable feet are in contact with the floor. Rotating the adjustable feet cannot compensate
for extremely uneven surfaces.
To level the equipment:
1. Try to shake the equipment. If there is any movement, tip the equipment to one side to locate the adjustable foot.
2. Correct the height of each adjustable foot as follows:
If you want to ...
Then turn the adjustable feet …
Raise the equipment
Counterclockwise
Lower the equipment
Clockwise
3. When you are finished adjusting the equipment, recheck for movement and readjust as necessary.
600 Line RBK Getting Started Guide | P/N 305386-101, ENU
© 2019 Precor Incorporated | 1 January 2019