Step 4
Attach the hitch arm assembly to the front of the
Sweeper Chassis Assembly using two 5/16” x 3/4”
Hex Head Bolts and two 5/16” Lock Nuts. Fig. 8
If you have trouble attaching the Hitch Arm Assembly,
try loosening the 5/16” x 3-1/4” Hex Head Bolt in order
for the Hitch Arms to spread apart easier.
Sweeper
Chassis
Assembly
Hitch Arm
Assembly
5/16” x 3/4”
Hex Head Bolt
Step 5
Insert the bottom of the Height Adjustment Tube
through the hole in the front of the Sweeper Chassis.
Be sure the Handle Grip on the Height Adjustment
Tube is facing forward. Attach the bottom of the Height
Adjustment Tube to the Bumper Assembly using a
5/16” x 2” Hex Head Bolt and a 5/16” Lock Nut. Fig. 9
Height
Adjustment
Tube
Bumper
Assembly
5/16” x 2”
Hex Head Bolt
Height
Adjustment
Bracket
Notch
Spring
Step 6
For Packaging purposes the Top Side Hamper
Tubes (2 - one each side) are put on upside-down.
Remove the nut on each end of the Tie Rod and
re-attach the Top Side Hamper Tubes as shown
in illustration. Fig. 11
Insert The Top Side Hamper Tube into the
end of the Top Hamper Cross Tube. There is
a spring button lock on the Top Side Hamper
Tube that will secure these two tube assemblies
together. Fig. 11
Top Side Hamper Tube
Assembled Correctly
Tie Rod
Attach these
two tube
assemblies
together
Attach the Bottom Hamper Cross Tube to the
two (one each side) Bottom Side Hamper Tubes.
The two holes in the Bottom Hamper Cross
Tube need to face out as shown in the illustration.
Fig. 12 These holes are for the Hamper Support
Rods, attached later in this assembly.
Push the Bottom Hamper Cross Tube down while
pulling up on the Top Hamper Cross Tube, this
creates the extended Hamper Assembly. Fig. 12
Finally, insert one end of the Hamper Support Rod
into the Top Hamper Cross Tube hole and the
other end of the Hamper Support Rod into the Bottom
Hamper Cross Tube hole. Fig. 13 Repeat this process for
the other Hamper Support Rod on the other side of
the Hamper Assembly.
Bottom Hamper Cross Tube
Side Hamper
Tubes
Top Hamper Cross Tube
Bottom Hamper
Cross Tube
Hamper Support Rod
Attach the optional Wind Apron to the
outside tubes towards the front of the
Hamper Assembly. Fig. 14
The Wind Apron helps keep debris from
blowing out of the Hamper Assembly while
the unit is in use.
Wind Apron
5/16” x 3-1/4” Hex
Head Bolt
Fig. 8
Fig. 9
Fig. 10
Notch
Adjustment Bracket
Fig. 11
Spring
Button
Lock
Fig. 12
Hole in Bottom
Cross Tube
Hole in Bottom Cross Tube
Push
Down
l
Pu
l Up
Hole in Bottom
Cross Tube
Fig. 13
Fig. 14
Attach one end of the Spring to the notch on the height
adjustment bracket. Pull the Spring around and behind
the Height Adjustment Tube. Attach the other end of
the Spring to the opposite notch. Fig. 10
Step 3
Attach both Hitch Arms together using
one 5/16” x 3-1/4” Hex Head Bolt and
one 5/16” Lock Nut. Fig. 6 Do not tighten
this bolt yet.
Attach both Clevis Plates to the end of
the Hitch Arms. One 5/16” x 2-1/4”
Hex Head Bolt is attached in front
of the 5/16” x 3-1/4” Hex Head Bolt that
was used to connect the Hitch Arms.
The other 5/16” x 2-1/4” Hex Head Bolt
needs to be behind the Hitch Arm Bolt.
Tighten the Hitch Arm bolt then the two
Clevis Plate Bolts. Fig. 7 This arrangement
keeps the Clevis Plates from slipping off
the end of the Hitch Arms while in use.
Hitch Arms
5/16” x 3-1/4”
Hex Head Bolt
5/16” Lock Nut
Clevis Plate
5/16” x 3-1/4”
Hitch Arm
Bolt
Clevis Plate
FRONT 5/16” x 2-1/4”
Hex Head Bolt
BACK 5/16” x 2-1/4”
Hex Head Bolt
Fig. 6
Fig. 7
