P
RO
V
U
™ PD6001 Analog Input Feet & Inches Meter
Instruction Manual
21
Display Functions & Messages
The meter displays various functions and messages
during setup, programming, and operation. The
following table shows the main menu functions and
messages in the order they appear in the menu.
Display Functions & Messages
Display
Parameter
Action/Setting
Description
setup
Setup
Enter
Setup
menu
Input
Input
Enter
Input
selection menu
nmA
4-20 mA
Set meter for 4-20 mA
input
Volt
0-10 VDC
Set meter for
10 VDC
input
d-SCAL
Dual-scale
Press Enter to select dual-
scale display for some level
applications (Select Yes or
No)
units
Units
Select the display
units/tags
Dec pt
Decimal
point
Set decimal point
PV 2
PV2
PV2 decimal point (Level)
prog
Program
Enter the
Program
menu
SCALE
Scale
Enter the
Scale
menu
SCAL 1
Scale 1
Enter the
Scale
menu for
PV1
SCAL 2
Scale 2
Enter the
Scale
menu for
PV2
Cal
Calibrate
Enter the
Calibration
menu
Inp 1
Input 1
Calibrate input 1 signal or
program input 1 value
Dis 1
Display 1
Program display 1 value
Inp 2
Input 2
Calibrate input 2 signal or
program input 2 value
(up to 32 points)
Dis 2
Display 2
Program display 2 value
(up to 32 points)
Error
Error
Error, calibration not
successful, check signal or
programmed value
dsplay
Display
Enter the
Display
menu
Line 1
Display
line 1
Press Enter to access
Line 1 display format and
parameter options
(default: PV)
Fornmt
Format
Format fractional inches to
either eighths (1/8) or
sixteenths (1/16)
Paranm
Parameter
Press Enter to assign the
Main display parameter
(default: PV)
Dset 1
*
Display
set 1*
Display relay 1 (*through 8)
set point
D Hi
Display
high
Display high value
D lo
Display low
Display low value
Display Functions & Messages
Display
Parameter
Action/Setting
Description
D Hl
Display
hi/low
Alternate between high/low
value
nm bus
Display
Modbus
Display Modbus input
register
D pV
Display PV
Select to display PV
Line 2
Display
line 2
Press Enter to assign the
Line 2 display parameter
(default: engineering units)
D unit
Display unit
Display units on line 2
D pV2
Display
PV2
Select to display PV2
(dual-scale display)
D pCt
Display
PCT
Select to display percent of
PV1 (dual-scale display)
D l-u
Display
Level Units
Select to display PV1 level
in decimal units on display
line 2
D off
Display off
Turn off display line 2
d-Inty
Display
intensity
Set display intensity level
from 1 to 8
RELaY
Relay
Enter the
Relay
menu
RLY 1
*
Relay 1*
Relay 1 (*through 8) setup
Note: Relays 5-8 are
shown only if expansion
relay module is installed.
Only relays 1-4 are
available in the base
model.
Act 1
Action 1
Set relay 1 action
Auto
Automatic
Set relay for automatic
reset
A-nman
Auto-
manual
Set relay for automatic &
manual reset any time
LatCH
Latching
Set relay for latching
operation
Lt-CLr
Latching-
cleared
Set relay for latching
operation with manual
reset only after alarm
condition has cleared
Altern
Alternate
Set relay for pump
alternation control
Sanmpl
Sampling
Set relay for sampling
operation
OFF
Off
Disable relay and front
panel status LED (Select
Off to enable Interlock
feature)
Set 1
Set 1
Program set point 1
RSt 1
Reset 1
Program reset point 1
FaiLSF
Fail-safe
Enter
Fail-safe
menu
FLS 1
Fail-safe 1
Set relay 1 fail-safe
operation
on
On
Enable fail-safe operation
off
Off
Disable fail-safe operation
FLS 2
Fail-safe 2
Set relays 2-8 fail-safe
operation
