Precision Digital Corporation PD6622-L2N Скачать руководство пользователя страница 10

Страница: 10 / 45

Loop Leader PD6620 Series Loop-Powered Flow Rate/Totalizers

Instruction Manual

I.S. Equipment

Entity

Parameters

Required

Relationship

Between Entity

Parameters

I.S. Barrier Entity

Parameters

V max (or Ui)

≥

Voc or Vt (or Uo)

I max (or Ii)

≥

Isc or It (or Io)

P max, Pi

≥

Ci + Ccable

≤

Ca (or Co)

Li + Lcable

≤

La (or Lo)

•

For Division 2 and Zone 2 Applications:

Division 2 and Zone 2 installations do NOT require

the use of an intrinsically-safe barrier or

intrinsically-safe entity parameters. Class I,

Division 2, Groups A, B, C, and D T4 and Class I,

Zone 2, Group IIC T4, -40C <= Ta <= +70C.

Ratings: V = 30 V dc, I = 30 mA; Relay Ratings:

250V ac/dc 1A

For North American Community:

Installation and service of this device and/or

associated apparatus (barrier) should be performed

only by trained service personnel

and must be installed in accordance with the

manufacturer’s control drawing, Article 504 of the

National Electric Code (ANSI/NFPA 70) for installation

in the United States, or Section 18 of the Canadian

Electrical Code for installations in Canada.

•

EXPLOSION HAZARD

– Do not disconnect

equipment unless power has been removed or the

area is known to be non-hazardous

•

RISQUE D’EXPLOSION

– NE PAS BRANCHER NI

DÉBRANCHER SOUS TENSION.

Year of Construction

This information is contained within the serial number

with the first four digits representing the year and

month in the YYMM format.

Safety Information

• Read complete instructions prior to installation and

operation of the meter.

• Risk of electric shock or personal injury.
• Hazardous voltages exist within enclosure.

Installation and service should be performed only

by trained service personnel.

• Service requiring replacement of internal

components must be performed at the factory.

• Control room equipment must not use or generate

more than 250 VRMS or VDC.

• Hazardous location installation instructions for

associated apparatus (barrier) must be followed

when installing this equipment.

• For safe installation of an ATEX approved

transmitter in series with PD6626/PD6628 loop-

powered meters, the hazardous location installation

instructions for the transmitter, PD6626/PD6628

loop-powered meter, and associated apparatus

(barrier) must be compatible.

• PD6626/PD6628 Series Loop-Powered meters do

not add capacitance or inductance to the loop

under normal or fault conditions.

• Substitution of components may impair hazardous

location safety.

• Equipment contains non-metallic materials and

therefore special care and consideration should be

made to the performance of these materials with

respect to chemicals which may be present in a

hazardous environment.

Содержание PD6622-L2N














































Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды

Precision Digital Corporation PD6622-L2N, Инструкция по эксплуатации

Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды