Pratica Copa Express Скачать руководство пользователя | Manualshive

Страница: 100 / 130

background image

94

POWER COMPONENTS

Ventilation System

The Copa Express oven ventilation system uses four 3100 RPM cooling fans (dimensions: 5in/120mm
x 5in/120mm) that exhaust all of the hot air from the motor, electronic compartment and high voltage
compartment. To exhaust all of the hot air from the magnetrons the Rocket Express oven uses one
2800 RPM sirocco fan.

Testing Cooling Fans

WARNING:

For safety purposes, manually discharge capacitors before troubleshooting

cooling fans due to proximity.

1)

Unplug the unit and remove the rear panel.

2)

Manually verify the cooling fan spins freely and not seized.

•

If cooling fan is seized / not spinning, replace the cooling fan.

3)

Disconnect the cooling fan cables from the connectors and check for continuity.

•

If the meter registers continuity, then the cooling fan is fine.

•

If the meter registers no continuity or open, replace the cooling fan.

Electronic

Compartment

hot air outlet

Magnetrons

hot air outlet

Motor

hot air outlet

High voltage

hot air outlet

«
...
98
99
100
101
102
...
»

Содержание Copa Express



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Copa Express

Бренд: NEFF Страницы: 40

Бренд: Salva Страницы: 73

DOC30 977D Series

Бренд: Dacor Страницы: 84

Dominator Plus G3151

Бренд: Falcon Страницы: 10

Бренд: Oster Страницы: 10

Бренд: Wolf Страницы: 8

Combi Duo 6x1/1 GN / 6x1/1 GN

Бренд: Rational Страницы: 20

Бренд: Gaggenau Страницы: 60

Бренд: Daewoo Страницы: 39

Бренд: Zline Страницы: 39

Бренд: MBM Страницы: 83

Бренд: Daewoo Страницы: 12

Бренд: cecotec Страницы: 31

Бренд: Atag Страницы: 54

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 34

Бренд: Panasonic Страницы: 39

Бренд: Panasonic Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды