Pratica Copa Express Скачать руководство пользователя

Страница: 14 / 130

SPECIFICATIONS & INSTALLATIONS

Installation Warnings: Please read before lifting
oven to prevent injury

WARNING:

This unit weights approximately 174 lbs. (79kg). Never attempt to lift this unit with

fewer than 2 people.

WARNING:

The oven must be properly installed on a level surface at all times. Pratica Inc. will

not recognize damage from a fallen oven as a warranty and may void warranty all together.

WARNING:

Never lift the oven up by the door handle. Doing so may cause the door to misalign

or cause damage to door hinges which will not be covered by warranty.

WARNING:

Never lift the unit from the removable front panel under the door as it may get.

Damaged or may come loose while lifting.

WARNING:

This unit is not meant to be stacked. Please contact Pratica Inc. for further details.

WARNING:

This unit is not meant to be installed in an enclosed area without proper

ventilations. Damage may occur to components is oven installed in a structure that has 5 or
more sides preventing the minimum 4-6in clearance on side and 6-12in clearance from back
to wall.

Содержание Copa Express



































































































































Результаты поиска

Содержание Copa Express

Отзывы:

Похожие инструкции для Copa Express

Бренды по названию

Популярные бренды

Pratica Copa Express, Руководство по обслуживанию

Результаты поиска

Содержание Copa Express

Отзывы:

Похожие инструкции для Copa Express

Бренды по названию

Популярные бренды