Control unit for 1 device with max power 1000W.
110/240 VAC power supply, integrated RX 433.92 MHZ ISM,
wired input settable with button or switch.
Presence simulation function, On/Off, timer ON.
DOM1
-L1SIM
FLASHES
TYPE OF SWITCH-ON
PROGRAMMED
Duration of 4 hours, followed by 20 hour pause
Duration of 8 hours, followed by 16 hour pause
Duration of 12 hours, followed by 12 hour pause
Continuous presence simulator cycle
1 flash
2 flashes
3 flashes
4 flashes
Default: duration 4 hours, pause 20 hours
This procedure is used to set the duration of the presence simulator.
WARNING: the presence simulator function is repeated every day at the same time until it is deactivated with a command by radio
or wire (see paragraph 6.1).
PROCEDURE
1- Position DIPs 1, 2, 3 and 4 to
ON-ON-OFF-OFF
2-
Press the button on the receiver for a short time.
The LED comes on and stays on
3- Press the button on the receiver for a short time.
4- The LED on the receiver flashes.
Each flash corresponds to a setting
5- Press the button for a short time during the
desired flash
WARNING: to change the setting, repeat the procedure from point 1
WARNING: after programming, reposition the dip switches to the desired operation of the
contacts (see paragraph 4.1)
6.3
SETTING THE DURATION OF THE PRESENCE SIMULATOR
ON
1 2 3 4
ON
1 2 3 4
6.4
RADIO PROGRAMMING OF TRANSMITTERS MATCHED TO THE
ACTIVATION OF THE PRESENCE SIMULATOR CYCLE
This process makes it possible to programme only compatible transmitters; see table 6.4.
It will be possible to activate and deactivate the presence simulator cycle with a transmission from the programmed transmitter.
By programming the same channel of a transmitter on multiple receivers with this function it will be possible to create a system in
which the lights in multiple rooms will turn on in a random sequence (see paragraph 6.1).
PROCEDURE:
1- Position DIPs 1, 2, 3 and 4 to
OFF-OFF-OFF-OFF
2- Press the button on the receiver for a short time. The LED comes on and stays on.
3- Make a transmission with the remote control to be saved (see transmitter manual, the paragraph entitled "transmitter program-
ming"). The LED on the receiver flashes 3 times to signal that it has been received.
4- The control unit listens for 30 seconds (to immediately exit the procedure press the button on the receiver).
WARNING: after programming, reposition the dip switches to the desired operation of the
contacts (see paragraph 4.1)
If the transmitter is a multifunctional one, the key dedicated to activation will be the "square" one.
To delete programmed transmitters from the memory, see paragraph 5.4.
Tab. 6.4
COMPATIBLE TRANSMITTERS
INDEX
1 - PRODUCT FEATURES
1.1 - TECHNICAL DATA
1.2 - DESCRIPTION
2 - ELECTRICAL CONNECTIONS
2.1 - CONNECTIONS FOR LOADS POWERED BY THE GRID
2.2 - CONNECTION BETWEEN TWO CLEAN OUTPUT CONTACTS
3 - USE OF THE CONTROL UNIT
3.1 - USE VIA RADIO
3.2 - USE VIA WIRE
4 - CONTROL UNIT SETTINGS
4.1 - SETTING "OUT1" OUTPUT
4.2 - SETTING "OUT1" TIMING
4.3 - SETTING TYPE OF INPUTS VIA WIRE "P1"
5 - RADIO PROGRAMMING
5.1 - RADIO PROGRAMMING MULTIFUNCTIONAL TRANSMITTERS
5.2 - RADIO PROGRAMMING OF GENERIC TRANSMITTERS
5.3 - DELETION OF TRANSMITTERS
6 - PRESENCE SIMULATOR
6.1 - USE OF PRESENCE SIMULATOR
6.2 - SETTING RANDOM SWITCH-ONS
6.3 - SETTING THE DURATION OF THE PRESENCE SIMULATOR
6.4 - RADIO PROGRAMMING OF TRANSMITTERS MATCHED TO THE ACTIVATION
OF THE PRESENCE SIMULATOR CYCLE
ISDOM
-L1SIM_EN_V1.1
PRASTEL France
ZI Athelia II
225 impasse du Serpolet
13600 La Ciotat
Tél : 04 42 98 06 06
prastel.com
DOM-TX15, DOM-TX4, MPSTP2E, TC2E, TC4E, SLIM2E, SLIM4E
