background image

 

The brightness decreases obviously   

 

Ambient  temperature  is  too  hot  which  makes  the  projector  too  hot, 
please take appropriate ventilation measures   

3.

 

APPEARANCE   

 

 

4.

 

INSTALLATION   

 

RIGGING   

Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole unit on the truss, 
tighten the clamp’s retainers to keep the unit stable. (See the 

WARNING

 on the underside of the base as shown above) 

To pass the 

SAFETY CORD through the ARM for safety!

 Always ensure that the unit is firmly anchored to avoid vibration and slipping whilst 

functioning. Always ensure that the structure that you are going to mount the unit to is secure and strong enough to support the weight 
of the unit Loosen the big knob and adjust the head’s angle for the effect desired and the tighten it. The installation is completed. 
(if the unit is wit wireless control, while being hung, the antenna should face down) 
 

PLACE A UNIT ON A FLAT SURFACE 

 

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support 
60degrees. Tighten the small knob. Loosen he big knob and adjust the angle between the arm and unit as desired and then tighten it. 
.(If the unit is with wireless control, after the unit is placed on a flat surface the antenna should face up) 
 

Arm

Safety Clamp

Warning

For safety, please 

run the safety cord 
through the safety cord 
hole and ensure it is 
tightened .

Body 

Arm 

Содержание LS 150 Water

















Отзывы: