manualshive.com logo in svg

PPI SMART MONITOR, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
PPI SMART MONITOR Скачать руководство пользователя страница 16

16

DOES THE SMART ROLL REQUIRE MAINTENANCE?

Maintenance is minimal, check the roll periodically as you would any idler roll for ease of turning and for buildup on the roll . Also make sure 
that the CSR is free and rolls smoothly on the belt surface .  If mounted properly, it should give years of service .

WHY ISN’T MY SMART MONITOR RAMP-UP TIMER DOING ANYTHING WHEN I START MY CONVEYOR?

See the two options for wiring the Smart Monitor in Section 4 “Wiring the Smart Monitor” . The ramp-up timer will only keep the relay 
energized when the Smart Monitor first receives power . When 120 VAC is applied to the power cable, the timer function will energize the 
control relay . After the time has elapsed the relay will de-energize unless the belt is running above the set speed .

 

UNIVERSAL MOUNT SMART ROLL MOUNTING INSTRUCTIONS

Attention must be given to the location of the Smart Roll so that it is always in contact with the belt . Failure to mount properly may void 
warranty and could cause damage to conveyor belt and other components . 

Содержание SMART MONITOR

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды