background image

5

NOTE:

There is a valve in the upper compartment that either

sends the water through the heating components, or bypasses
them.  The machine is preset in the “HOT” position. To clean
with cold water, turn the valve to “COLD” or UP position.  This
should be done prior to filling the tank with water.  For gener-
al cleaning, it is recommended leaving the valve in the “HOT”
or down position and cleaning with hot water.

Maintenance

To receive reliable service from this equipment, regular daily
maintenance is a requirement. Fabric cleaning, both carpet
and upholstery, are very dirty environments for any equipment.
The following recommendations are offered.

1. Keep the equipment clean, both inside and out.

2. Lubricate brass quick disconnects and drain valves with 

a quality lubricant such as WD-40.

3. Flush solution systems after use with clear, clean water.

(A white vinegar solution may also be used).  This will 
counter-act hard water and alkaline deposits and aid 
in keeping orifices clean.

4. Do not allow fluid either in solution or waste tank to sit 

overnight. The unit should be emptied and cleaned daily.

5. Clean the strainer in the solution tank, the filters on the

vacuum stack in vacuum tank and all lint filters in the  
inlet or vacuum tanks daily.

6. Do not use the same receptacle (pail) to fill solution 

tank that is used to remove waste from vacuum tank.

7. When the unit is not in use, leave the vacuum tank lid 

open.

8. At the end of each day, run the vacuum for 3 minutes 

with lid open and filter off.

Safety Precautions

These precautions are designed with the safety of the operator,
the equipment, and others in mind and must be followed at all
times to avoid serious personal harm and/or death, and dam-
age to the unit.

1. Always use a grounded electrical outlet.

2. Always disconnect electric cable from electrical outlet 

before attempting to make any adjustments or repairs.

3. Never use this equipment as a toy.

4. Never use equipment near or around flammable or 

explosive materials, fuels, or solvents.

5. Never put flammable materials, fuels, or solvents 

into equipment.

6. Never lift the machine by the drain hose. 

7.

Do not allow the unit to freeze!

8. The equipment was not designed to be used outdoors 

switch panel

valve

Содержание PF1352













Отзывы: