background image

INSTALL AND CHANGE THE BLADE 

Refer to Figure 7, 8 and 9

Turn the switch to OFF position and disconnect the ma-
chine from power source. 

CAUTION:

 Wear gloves while installing and removing the 

saw blade 
1. Remove the table insert. 
2. Raise the blade arbor to the maximum height by turning  
  the blade elevation control wheel counter-clockwise.

Figure 7

3. Remove the arbor nut and flange.
4. Install the saw blade onto the arbor with the blade teeth  
  pointing toward the fornt of the saw. 
5. Install the flange against the blade and thread the arbor  
  nut as far as possible by hand. Ensure that the blade is  
  flush against the inner blade flange.

Figure 8

Figure 9

6. To tighten the arbor nut, use the open end wrench and  
  align the wrench jaws on the flats of the flange to keep  
  the arbor from turning.
7. Place the box and wrench on the arbor nut, and turn    
  clockwise (to the rear of the table saw).
8. Lightly insert the rear part of the table insert into table,  
  and pull down its front part in table recess to lock.

BLADE GUARD ASSEMBLY

Refer to Figure 10

Turn the switch to OFF position and disconnect the 
machine from power source.

POSITION THE  RIVING KNIFE

1. Remove the table insert.
2. Set the blade to the maximum height and the tilt to zero  
  degrees on the bevel scale. 
3. Rotate the riving knife release lever clockwise, so that it  
  points upward.
4. Pull riving knife towards release lever to disengage it    
  from the pins.
5. Slide the riving knife up to its highest position, so that it  
  is directly over the center of the blade.
6. Align holes in riving knife with pins and lock the release  
  lever by rotating  it counterclockwise. Push/Pull riving   
  knife to verify that it is locked in place.
7. Replace table insert. 

Figure 10

Figure 11

BLADE GUARD INSTALLATION

Blade guard installation
1. Hold the front of the barrier guard assembly by the    
  metal “fork” with one hand. Hold the guard release  

 

  lever up with the other hand.
2. Lower the rear of guard assembly and slip the cross    
  bar into the rear notch on top of the riving knife.
3. Lower the front of the guard assembly until the metal    
  “fork” is parallel with the table.
4. Press down on the guard release lever until you feel    
  and hear it snap into the locking position. Check that    
  the guard assembly is securely connected. 

4

ASSEMBLY

     WARNING

     WARNING

Blade Arbor

Arbor Nut

Blade Flange

Riving Knife

Open-end
Blade Wrench

Saw Blade

Screws

Release Lever

Release Lever

Riving Knife

Pin

Содержание TS1001





















Отзывы: