• The operator must maintain a secure body position and
have a firm grip and footing when using this tool .
• This tool is not electrically insulated . Never use the
tool if there is any chance of it coming into contact with
live electricity .
CAUTION
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used .
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
AIR SUPPLY SETUP AND CONNECTION
Refer to Figure 1
• Figure 1 shows the recommended air supply hook-up .
• The use of air line lubricators and air line filters is
recommended to prevent water in the line that can
damage the tool . Drain the air tank daily . Clean the
air inlet filter screen on at least a weekly schedule
to remove accumulated dirt or other matter that can
restrict air flow .
• The tool’s air inlet used for connecting an air supply has
a standard 1/4” NPT American thread .
• If an air line lubricator is not used, before operating the
tool add a few drops of Pneumatic Tool Oil into the tool
inlet . Repeat each hour of constant use .
CAUTION
This air tool requires lubrication BEFORE initial use and
before and after each additional use .
OPERATION
CAUTION
Never mount a grinding wheel on a sander . A grinding
wheel that bursts can cause very serious injury or death
when not properly guarded .
• Ensure the sanding pad is fixed securely to the tool .
Use the supplied wrench to hold the shaft nut in place
while turning the sanding pad clockwise to tighten and
counterclockwise to loosen .
• Select the correct 6" abrasive disc for the job . Use 6"
self adhesive abrasive disc .
• Connect to suitable air supply as recommended .
CAUTION
Risk of unsafe operation . Firmly grasp air hose with hand
when installing or disconnecting to prevent hose whip .
• Touch the sander lightly to the work and allow
the abrasive disc to cut . Take care when sanding
around sharp edges and surfaces to avoid the disc
snagging, the disc may be brought to an abrupt stop
or considerably slowed, causing the tool to kick in
the hands .
• Do not continue to use abrasive discs that are worn or
clogged . Do not use undersized or oversized abrasive
discs . The disc should be no more than 1/4" larger in
diameter than the sanding pad, and not smaller than the
sanding pad .
Key# Part#
Description
1
AS631601
Housing
2
AS631602
Spring Pin (3*40L)
3
AS631603
Air Inlet
4
AS631604
Throttle Lever
5
AS631605
Shaft
6
AS631606
Bushing
7
AS631607
O-Ring (21 .5*1 .5)
8
AS631608
O-Ring 2 (10 .7*1 .5)
9
AS631609
O-Ring (10 .5*1)
10
AS631610
Regulator
11
AS631611
Silencer
12
AS631612
Adapter
13
AS631613
Spring Pin (2*18L)
14
AS631614
Rear End Plate
15
AS631615
Rotor
16
AS631616
Rotor Blade(5)
17
AS631617
Screw (M5*12L)
18
AS631618
Cylinder
19
AS631619
Front End Plate
20
AS631620
Swivel Exhaust
21
AS631621
O-Ring (3 .68*1 .78)
22
AS631622
Retaining Ring (STW-14)
23
AS631623
Spring
24
AS631624
Retainer Ring
Key# Part#
Description
25
AS631625
Nut (M5*0 .8)
26
AS631626
Ball Bearing (6000zz)
27
AS631627
Spring Pin (3*28)
28
AS631628
O-Ring (5*2)
29
AS631629
Lock Ring
30
AS631630
Grip Hat
31
AS631631
Shroud
32
AS631632
Ball Bearing (6001zz)
33
AS631633
Washer
34
AS631634
Shaft
35
AS631635
Snap Ring
36
AS631636
Key
37
AS631637
Balancer Shaft
38
AS631638
Washer (3*13)
39
AS631639
Spanner
40
AS631640
O-Ring (39 .4*3 .1)
41
AS631641
O-Ring (8 .8*1 .7)
42
AS631642
O-Ring (2*1)
43
AS631643
O-Ring (13 .5*1 .5)
44
AS631644
Ball Bearing (6001)
45
AS631645
Ball Bearing (6001P)
46
AS631646
Pad (6")
47
AS631647
Stopper
48
AS631648
Washer
Figure 1
Tailpiece
Adaptor
Adaptor
Main Air
Hose
Whip Hose
Coupler
Coupler
Oiler
Filter
DRAIN
DAILY
Regulator
PIPES AND
FITTINGS
Stop Valve
Tailpiece
Adaptor
OIL HERE
DAILY
Tailpiece
Adaptor
