background image

 

POWX093 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

6

 

www.varo.com 

 

Ensure that milling cutter is firmly clamped. 

 

Use only milling cutters for routers; never use e.g. milling cutters for drilling machines or 
stationary machines. 

 

Use only commercially available milling cutters for routers with a shank diameter 6 mm or 
8 mm. 

 

Always use both hands to guide the tool. 

 

Never wedge the ON switch fast. 

 

Never reach into the milling zone while the tool is running. 

 

Feed only running milling cutters to the material. 

 

Note direction of cut - always move the cutter against the material. 

 

When work is finished, remove the milling cutter from the tool. 

 

Wood dust set up during work is harmful to health. Always work with dust collector 
operating. 

 

Wear protective goggles, ear protectors and, if necessary, breathing mask. 

 

Observe general safety regulations for handling and using electric tools.. 

7  OPERATION 

7.1 

Depth Stop 

 

Locate  the  depth  stop  on  the  left-hand  side  of  the  cutting  machine.  This  continuously 
adjustable stop is intended to limit the depth of the cut. Locate the fixing screw for the depth 
stop (1). Loosen it by turning it in anticlockwise direction. To move the depth stop up or down, 
turn the stop adjuster in clockwise or anticlockwise direction (2). 

7.2 

Locking lever for cutting machine body 

 

When viewed from the front, the locking lever (3) is located at the rear on the left-hand side. 
The  cutting  machine  body  is  spring-tensioned.  Take  care  when  releasing  the  locking  lever. 
Grasp  both  handles  and  brace  yourself  before  releasing  the  lever  (4).  Press  downwards  to 
allow the cutting machine body to move down. When you reduce the downward pressure, the 
springs force the cutting machine body back up into its highest position. 

CAUTION

: The housing of the machine is under spring tension. When you release the locking 

lever, it returns to its highest position.. 

Содержание POWX093














Отзывы: