background image

 

POWX07583 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

6

 

www.varo.com 

 

Before each use, check the saw blade for small cracks or damages. Replace a cracked or 
damaged blade immediately. 

 

Never use saw blades made of high-speed steel (HSS). 

 

Only use saw blades that are recommended by the manufacturer and that fulfil the EN847-
1 standard. Also make sure the riving knife is not thicker than the width of the saw cut, and 
that it is not thinner than the body of the saw blade. 

 

Always use the accessories that are recommended by this manual. 

 

Select the correct saw blade for the material must be sawn. 

 

To reduce the generation of noise, always make sure that the blade is sharp and clean.  

 

Only use correctly sharpened saw blades. Never exceed the maximum speed that is 
indicated on the saw blade. 

 

Before installing the saw blade, clean the axle, the flanges (especially the assembly 
surfaces) and the hexagonal nut. Incorrect mounting can lead to vibrations/knocking or 
slipping of the saw blade. 

 

Wherever possible, use the upper saw blade guard and the riving knife with every type of 
application, also when sawing material in two. Always mount the saw blade guard 
according to the instructions in this manual. Cutting operations are those where the saw 
blade cuts completely through the workpiece, such as for instance when doing longitudinal 
cuts or shortening workpieces. NEVER use the equipment with a defective saw blade 
guard, and never tie up a saw blade guard with a rope or cord. Every irregularity in the 
operation of the saw guard must be immediately corrected. 

 

Immediately replace the upper saw blade guard and the riving knife, after a process has 
been completed that required their removal. 

 

Prevent that the saw comes into contact with metals, such as nails and screws. Search for 
and remove all nails, screws and other foreign materials from the workpiece, before you 
start to work. 

 

Remove spanners, cut off pieces and the other items from the saw table, before turning on 
the switch. 

 

NEVER wear gloves while working; the wearing of gloves is only recommended while 
cutting tools are being replaced. 

 

Make sure that your hands stay clear of the cutting line of the saw blade. 

 

NEVER stand in the cutting line of the saw blade and NEVER let anyone else stand in that 
position. 

 

Make sure that the saw blade does not touch the riving knife or the workpiece, before you 
turn on the switch. 

 

Let the saw run for a few moments before inserting a workpiece.  Listen for vibrations or 
knocking of the saw blade, which can indicate improper mounting or balancing of the 
blade. 

 

The equipment may not be used for making grooves or recesses. 

 

Replace the table insert when it is worn out. 

 

NEVER make any adjustments on the machine while it is turning. Remove the plug from 
the socket before making any adjustments. 

 

If necessary, use a push block. A push block MUST be used for longitudinal sawing of 
smaller workpieces, so that your hands and fingers are kept well away from the saw blade. 

 

Always store your push block, whenever it is not in use. 

 

Pay special attention to the instructions that help to reduce the hazard of KICK BACK. 
KICK BACK is a sudden reaction to a jammed, bent or badly aligned saw blade. KICK 
BACK causes the workpiece to be thrown back in the direction of the operator. KICK 
BACK can lead to serious injuries. KICK BACK can be avoided by keeping your saw blade 
sharp, by keeping the rip fence parallel to the saw blade, by maintaining the riving knife 
and the upper saw blade guard in good condition and in the right position, by keeping a 
good grip on the workpiece until you have pushed it completely past the saw blade, and by 

Содержание 166914

















Отзывы: