background image

 

16

Troubleshooting: Mechanical & Electrical Problems 

Trouble Probable 

Cause 

Remedy 

Board thickness does 
not match digital 
display 

Digital display not calibrated properly. 

Follow calibration procedures. 

Inadequate chain tension. 

Adjust chain tension. 

Sprockets misaligned. 

Align sprockets. 

Chain jumping 

Sprockets worn. 

Replace sprockets. 

No incoming power. 

Verify unit is connected to power, and 
main switch is set to “I”. 

Overload automatic reset has not 
reset. 

When planer overloads on the circuit 
breaker built into the motor starter, it 
takes time for the machine to cool 
down before restart. Allow unit to 
adequately cool before attempting 
restart. If problem persists, check 
amp setting on the motor starter 
inside the electrical enclosure. 

Planer frequently trips. 

One cause of overloading trips which 
are not electrical in nature is too 
heavy a cut. The solution is to take a 
lighter cut. If too deep a cut is not the 
problem, then check the amp setting 
on the overload relay. Match the full 
load amps on the motor as noted on 
the motor plate. If amp setting is 
correct then there is probably a loose 
electrical lead. Check amp setting on 
motor starter. 

Building circuit breaker trips or fuse 
blows. 

Verify that planer is on a circuit of 
correct size. If circuit size is correct, 
there is probably a loose electrical 
lead. Check amp setting on motor 
starter. 

Loose electrical connections. 

Go through all the electrical 
connections on the planer including 
motor connections, verifying the 
tightness of each. Look for any signs 
of electrical arcing which is a sure 
indicator of loose connections or 
circuit overload. 

Machine will not 
start/restart or 
repeatedly trips 
circuit breaker or 
blows fuses. 

Motor starter failure. 

Examine motor starter for burned or 
failed components. If damage is 
found, replace motor starter. If motor 
starter looks okay but is still suspect, 
you have two options: Have a 
qualified electrician test the motor 
starter for function, or purchase a new 
starter and establish if that was the 
problem on changeout. (continued) 

Содержание WP2412





































Отзывы: