background image

 

2

Warranty and Service 

Powermatic

®

 warrants every product it sells against manufacturers’ defects. If one of our tools needs service or 

repair, please contact

 

Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. 

Warranty Period

 

The general warranty lasts for the time period specified in the literature included with your product or on the official 
Powermatic branded website.  

 

Powermatic products carry a limited warranty which varies in duration based upon the product. (See chart 
below) 

 

Accessories carry a limited warranty of one year from the date of receipt. 

 

Consumable items are defined as expendable parts or accessories expected to become inoperable within a 
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects. 

Who is Covered 

This warranty covers only the initial purchaser of the product from the date of delivery. 

What is Covered 

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty 
does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, 
improper repair, alterations or lack of maintenance. Powermatic woodworking machinery is designed to be used with 
Wood. Use of these machines in the processing of metal, plastics, or other materials outside recommended 
guidelines may void the warranty. The exceptions are acrylics and other natural items that are made specifically for 
wood turning. 

Warranty Limitations 

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a 
Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

 

How to Get Technical Support 

Please contact Technical Service by calling 1-800-274-6846. 

Please note that you will be asked to provide proof 

of initial purchase when calling. 

If a product requires further inspection, the Technical Service representative will 

explain and assist with any additional action needed.

 

Powermatic has Authorized Service Centers located throughout 

the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service 
Center Locator on the Powermatic website.

 

More Information 

Powermatic is constantly adding new products. For complete, up-to-date product information, check with your local 
distributor or visit the Powermatic website. 

How State Law Applies 

This warranty gives you specific legal rights, subject to applicable state law.  

Limitations on This Warranty 

POWERMATIC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH 
PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW 
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 
POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR 
FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF 
OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. 
 
Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the official 
Powermatic website are given as general information and are not binding. Powermatic reserves the right to effect at 
any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem 
necessary for any reason whatsoever.  

Product Listing with Warranty Period  

90 Days – Parts; Consumable items 
1 Year – Motors, Machine Accessories 
2 Year – Woodworking Machinery used for industrial or commercial purposes 
5 Year – Woodworking Machinery 

 
NOTE:  Powermatic is a division of JPW Industries, Inc. References in this document to Powermatic also apply to 
JPW Industries, Inc., or any of its successors in interest to the Powermatic brand. 

Содержание OES9138

































Отзывы: