Powermatic 701 Скачать руководство пользователя страница 13

Страница: 13 / 20

Chisel Parallel to Workpiece

Referring to Figure 12:

The chisel can be adjusted parallel to the
workpiece as follows:

1. Loosen the two

clamps

(A) that secure the

fence

(B).

2. With

the

adjust knob

(C), move the fence back

far enough to insert the

workpiece

(D) between

the

chisel

(F) and

fence

(B). Raise the

workpiece hold-down

clamp

(E) if necessary.

3. With

the

operating handle

(G) bring the head

down until the chisel points are almost at the
table level.

4. Bring the

fence

(B) forward with the

adjust

knob

workpiece

(D) rests against the back surface of

the chisel (F), but do not force.

5. Loosen the chisel

lock handle

(H). This will

allow the chisel to rotate.

Further adjust the chisel by hand if needed.

6. Tighten

the

lock handle

(H) while making sure

the bushing maintains contact with the head
casting to preserve the clearance setting..

Figure 12

Содержание 701





















Результаты поиска

Содержание 701

Отзывы:

Похожие инструкции для 701

Бренды по названию

Популярные бренды

Powermatic 701, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 701

Отзывы:

Похожие инструкции для 701

Бренды по названию

Популярные бренды