PowerBoss Admiral 28 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 52

PowerBoss Admiral 28 Скачать руководство пользователя страница 16

16

Machine Overview

1.4

Control Console

For operator ergonomics, the control
console houses all the primary function
controls in a central area. The key
switch and optional headlight and off-
aisle wand switches are clustered in
the back portion of the console. The
directional switch (forward/reverse) is
located at the front of the console for
easy fingertip operation. The horn but-
ton, function selectors, and battery
gauge are located in the central part of
the console.

Key Switch (A) - S2

Controls the machine’s power (ON/
OFF) with a key for safety. All opera-
tional settings are retained even when
the power is turned off and on. This
also serves as a reset switch when
errors or faults occur.

Off Aisle Wand Switch (OPTIONAL)
(B) - S7 (281900 OPTION)

ON/OFF control for the water supply to
the wand and vacuum motor for the
optional Off-Aisle Wand.

Headlight Switch (OPTIONAL) (C) -
S10 (281990 OPTOION)

ON/OFF control for the optional head-
lights.

Battery Gauge (D) - BD1

Displays the level of charge remaining
in the machine’s batteries. The gauge
consists of 10 LEDs. (3 Green, 4
Amber, 3 Red) If the battery life is low,
the battery gauge bar icon will be flash-
ing to inform the operator that the
machine is almost out of power. Once

«
...
14
15
16
17
18
...
»

Содержание Admiral 28





















































Отзывы:

Нет отзывов