6. Put the chain in position and make sure that the loop is
behind the guide bar.
7. Hold the chain and bar.
8. Put the chain loop around the sprocket.
9. Make sure the chain tension pin hole on the guide bar fits
correctly with the bolt.
10. Install the chain cover.
11. Tighten the chain. Refer to
Adjust the chain tension.
12. Tighten the chain cover knob when the chain is well
tensioned.
NOTE
If you start the machine with a new chain, have a test for
2-3 minutes. After that, examine the tension again and
tighten the chain if necessary.
3.4
FIT THE POLE SAW
Figure 2-3
1. Mount the pole saw head on pole saw handle to achieve
the standard length.
2. Slide the collar upwards.
3. Turn the collar clockwise to tight it.
3.5
EXTENSION OF THE POLE SAW
Figure 2-3
1. Fit the extension pole between the pole saw handle and
the pole saw head to achieve the maximum length.
2. Slide the collars upwards.
3. Turn the collars clockwise to tight them.
WARNING
Periodically check the tightness of the connection of the
collars.
3.6
USE THE SHOULDER STRAP
Figure 4
1. Attach the carabiner to the carrying ring on the pole.
2. Put on the shoulder strap.
3. Adjust the length of the strap so that the carabiner is
about the width of a hand below your right hip.
3.7
CUTTING PREPARATION
Figure 4
Before you start to cut, make sure that
•
Wear heavy gloves for maximum grip and protection.
•
Maintain a proper grip on the machine during operation.
•
Use your right hand grip on the rear handle while
your left hand grip on the pole shaft.
•
Keep your body to the left of the chain line.
•
Never use a left-handed (cross-handed) grip, or any
stance that places your body or arm across the chain
line.
•
Never stand directly under the limb you are cutting.
•
Periodically examine the tightness of the collars during
operation.
3.8
INSTALL THE BATTERY PACK
Figure 5
WARNING
•
If the battery pack or charger is damaged, replace the
battery pack or the charger.
•
Stop the machine and wait until the motor stops before
you install or remove the battery pack.
•
Read, know, and follow the instructions in the battery
and charger manual.
1. Align the lift ribs on the battery pack with the grooves in
the battery compartment.
2. Push the battery pack into the battery compartment until
the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
3.9
REMOVE THE BATTERY PACK
Figure 5
1. Push and hold the battery release button.
2. Remove the battery pack from the machine.
4
OPERATION
NOTE
Remove the battery pack and keep hands clear of the lock
out button when you move the machine.
IMPORTANT
Examine the chain tension before each use.
4.1
EXAMINE THE CHAIN
LUBRICATION
NOTE
Do not use the machine without sufficient chain lubrication.
Figure 6
1. Examine the lubricant level of the machine from the oil
indicator.
2. Add the lubricant if it is necessary.
4.2
START THE MACHINE
Figure 7
6
English
EN
Содержание 1400173
