background image

BATTERY CHARGING

E

B9785b-0920

9

Use the charger in dry locations only.

ELECTRICAL HAZARD

Important Notes

• 

Your new battery must be charged for at least 18 hours before 
you use it in your vehicle for the first time.

•  We recommend that you start charging your battery before 

beginning assembly of your new vehicle. 

•  The battery must be upright while charging.
•  The charger is not a toy.
•  Do not short circuit the battery.
•  You do not need to remove the battery from your vehicle to 

recharge it.

•  Before charging the battery, examine the battery case for cracks 

and other damage which may cause sulfuric acid (electrolyte) to 
leak during the charging process. If damage is detected, do not 
charge the battery or use it in your vehicle. Battery acid is very 
corrosive and can cause severe damage to surfaces it contacts. 

•  Do not charge the battery on a surface (such as a kitchen counter 

top) which could be damaged by the acid contained inside the 
battery. Take precautions to protect the surface on which you 
charge your battery. 

•  Use only a Power Wheels

®

 12 volt charger with "12 V" connector 

(120 VAC, 60 Hz, 28W with an output of 12 VDC, 1200 mA) 
to charge your Power Wheels

®

 12 volt battery.

Adults Note:

 Regularly examine the charger for damage to the

cord, plug, housing or other parts that may result in the risk of fire, 
electric shock or injury. In the event of any damage, do not use
the charger until the damage has been properly repaired. Please
call 1-800-348-0751.
•  If your battery is old and will not accept a charge, do not leave it in 

the vehicle. Always remove a dead battery from the vehicle.

About Thermal Fuses

Your Power Wheels

®

 12 volt battery is equipped with a built-in 

thermal fuse. The thermal fuse is a self-resetting safety device which 
automatically “trips” and shuts down operation of the vehicle if the 
vehicle is overloaded or the driving conditions too severe. Once a 
fuse has “tripped”, it will automatically reset itself after approximately 
25 seconds and allow the vehicle to resume normal operations. 
To avoid repeated automatic shut-downs, do not overload the vehicle 
by exceeding the 130 lb. (59 kg) total maximum weight capacity 
(vehicle 90 lbs. - 41 kg; trailer 40 lbs. - 18 kg) or by towing anything 
behind the vehicle. Avoid severe driving conditions, such as driving 
up slopes or running into fixed objects, which can cause the wheels 
to stop spinning while power is still being supplied to the motors and 
make sure your child stops the vehicle before switching direction.
If a thermal fuse in a battery continually trips under normal driving 
conditions, please contact your local Power Wheels

®

 Authorized 

Service Center. For the location of the Authorized Service Center 
nearest to you, visit us on-line at 

www.powerwheels.com, 

or call

 1-800-348-0751.

• Battery can fall out and injure a child if 

vehicle tips over. Always use battery
retainer.

• 

PREVENT FIRE

 -  

Never modify the electrical system. 
Alterations could cause a fire resulting 
in serious injury and could also ruin the 
electrical system.

 -  

Use of the wrong type battery or charger 
could cause a fire or explosion resulting 
in serious injury.

 -  

 Use of Power Wheels

®

 components in 

products other than Power Wheels

®

 

vehicles could cause overheating, fire 
or explosion.

•  The battery must be handled by adults only. 

The battery is heavy and contains sulfuric 
acid (electrolyte). Dropping the battery 
could result in serious injury.

• Never allow children to charge the battery. 

Battery charging must be done by adults 
only. A child could be injured by the elec-
tricity involved in charging the battery.

• Never lift or carry the battery by the wires 

or connector. This can damage the battery 
and possibly cause a fire resulting in 
serious injury. Lift and carry the battery by 
the case only.

• Read the safety instructions on the battery.
• Examine the battery, charger and their 

connectors for excessive wear or damage 
each time you charge the battery. If 
damage or excessive wear is detected, do 
not use the charger or the battery until you 
have replaced the worn or damaged part.

WARNING

CAUTION

Содержание Kawasaki Adventure 4x4





























Отзывы: