background image

 

 

POWERKING                                                    1-800-344-3371                              [email protected] 

General Safety Rules 

 

Read this Safety & Operating Instructions manual before using your PowerKing Chipper 
Shredder. Become familiar with the operation and service recommendations to ensure 
the best performance from your machine. If you have any questions or need assistance, 

don’t hesitate to give us a call at 1

-800-344-3371 or send us an E-mail at 

[email protected]

. 

 

Safety Instructions 

The machine must not be used in any other way than described in the manual. 

Use only original equipment and spare parts. If you use non-approved spare parts, there 
is an increased risk and this is, therefore, not permissible. All liability is renounced in the 
event of an accident or other damage caused by the use of non-approved parts.  

Before using the machine for the first time, read and follow this manual 

Check Emergency Stop Switch before each operation. 

Make sure all bolts and nuts are properly tightened before operation. 

Choose a flat work place. Machine can only be used outdoors, away from flammable 
materials.  

User must wear close fitting work clothes, work gloves, eye protectors, ear plugs, dust 
proof mask and work boots. 

Before and after using the machine, proper maintenance is necessary. 

Failure to comply with these safety instructions could result in personal injury and/or 
damage to product or property. 

 

 

 

Содержание PK0903
















Отзывы: