AMP Load
Volts
Extension Cord Length
120V
25'
50'
100'
150'
AWG
1-5
18
16
16
14
6-10
18
16
14
12
10-12
14
14
14
12
12-16
14
12
Table 1
Minimum Recommended Extension Cord Gauge
FUNCTIONAL DESCRIPTION:
4-1/2" Angle Grinder
Volts ......................................... V
Amperes ................................... Amp
Alternating Current ................... ~
Double Insulated .......................
Hertz ........................................ Hz
Revolutions Per Minute ............ RPM
SPECIFIC SAFETY SYMBOLS
Used for the 4-1/2" Angle GrinderTool:
Extension Cords
1.
Make sure your extension cord is in good condition.
When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating.
2.
Select the correct size to use depending on Ampere (AMP) rating, cord length, Voltage
(Volts) and Gauge (AWG). If in doubt, use the next heavier gauge.
The smaller the gauge
number, the heavier the cord. Refer to Table 1.
3.
Outdoor Use Extension Cords.
When tool is used outdoors, use only extension cords intended
for use outdoors and so marked.
4.
Use only UL listed extension cords.
Inspect extension cord before use and never use damaged
altered extension cords. Follow extension cord manufacturer safety instructions.
Not recommended
LEGEND
1. Grip
6. Spindle Lock
2. On - Off Switch
7. Spanner
3. Power Cord
8. Grinding Wheel
4. Auxiliary Handle
9. Lock-on Button
5. Wheel Guard
1
2
3
4
5
6
7
8
9
Angle Grinder Trigger Switch
1.
(SEE FIGURE 1)
To start the grinder:
pull the
On-Off trigger switch (1).
To stop the grinder:
release the trigger switch.
2.
For continuous operation:
pull the trigger switch (1) and press the lock-on button (9).
The grinder will continue to run until the trigger is pulled fully and then released.
3
WARNING:
RISK OF PERSONAL INJURY.
Always disconnect the tool from the power
outlet before making any adjustment,
installing or changing the wheel.
CAUTION:
Never depress spindle lock button
while tool is in use and wheel is spinning.
Installing And Changing Wheels
1.
(SEE FIGURE 2)
Press the spindle lock button (1)
to stop the spindle from turning.
NOTE:
Spindle may require slight back and
forth rotation to engage lock.
CAUTION:
Always make sure the retaining
nut is securely tightened before operation.
2.
(SEE FIGURE 3)
Place the inner washer (2)
on the tool spindle and rotate if necessary
to engage the flats of the spindle.
3. Place a depressed center grinding wheel (3)
over the shoulder on the inner washer and
secure with retaining nut (4).
4. Using the spanner (5) provided, rotate the
retaining nut clockwise to tighten or
counter clockwise to loosen.
ASSEMBLY
1
1. Spindle Lock Button
Figure 1
Figure 2
2
3
4
5
2. Inner Washer
4. Retaining Nut
3. Center Grinding
5. Spanner
Wheel
Figure 3
4
Safety Warning For California Proposition 65
WARNING!
BREATHING HAZARD
1) Use of this tool may cause exposure to chemicals
that are known to the state of California to cause cancer, birth defects or other reproductive
harm. 2) Dust and debris created during cutting, drilling, grinding or sanding on some
materials may contain chemicals known to the State of California to cause cancer or birth
defects or other reproductive harm.
To reduce exposure to these chemicals, always use
approved safety equipment work in a well-ventilated area and wear dusk mask that
filters out microscopic particles.