background image

 

3

2. SAFETY GUIDELINES 

 
DEFINITIONS  

Safety symbols identify important safety messages that alert to the possibility of personal injury or death.  
Review them carefully before operating the unit and before performing maintenance or repairs. Check the rules 
and regulations at your location and identify possible hazards. The appropriate signal word for each message 
has been selected using the following guidelines: 

  

Danger indicates an immediate and specific hazard, which 

will

 result in 

severe

 

personal 

injury

 or 

death

 if the proper precautions are not taken.

 

 

-

 

Warning indicates a specific hazard or unsafe practice, which 

could 

result in 

severe 

personal injury

 or 

death

 if proper precautions are not taken.

 

  

- Caution indicates a potentially hazardous situation, which 

may

 result in 

minor

 or 

moderate 

injury

 if proper practices are not taken.

 

____________________________________________________________________________ 

IMPORTANT SAFETY INSTRUCTIONS  

 

   

Read and understand the operator’s manual and all safety alerts before operating or maintaining your 

pressure washer. Be certain that everyone operating this equipment is familiar with the recommended 
operating and maintenance procedures and follows all the safety precautions. Never let children or untrained 
adults operate the machine.

 

_______________________________________________________________________________ 

  

 

 

RISK OF FIRE OR EXPLOSION 

 

Spilled gasoline and its vapors can ignite from cigarette sparks, electrical arcing, exhaust gases, and hot 
engine components such as the muffler. Never refuel the engine while it is hot or running. Move unit away from 
refueling area before starting engine. Operate and fuel equipment in well-ventilated areas free from 
obstructions. 

 

RISK OF BURNS 

High temperatures are generated by the operation of the pressure washer.  Contact with hot surfaces, such as 
the engine exhaust components could result in a serious burn.  Allow them to cool off before handling or 
servicing.  Keep children away from the pressure washer at all times. 

 

   

RISK TO BREATHING 

Do not operate equipment in an enclosed area. Engine exhaust contains carbon monoxide, an odorless, 
colorless, deadly poison. 

 

 

HIGH PRESSURE FLUIDS 

Wear proper hand and eye protection when searching for a high-pressure leak.  Do not place hand or fingers 
in front of the nozzle or point spray at yourself or others.  In the event that high-pressure spray penetrates the 
skin, seek medical attention immediately. 

 

 RISK OF INJURY 

Do not operate with belt guard removed. Wait for all moving parts to stop before taking belt guard off for 
servicing. Belt guard must be fastened in place before starting the pressure washer. 

Содержание 2525DA






























Отзывы: