Powercraft
3
6. Do not force tool
It will do the job better and safer at the rate for which
it was intended.
7. Use right tool
Do not force small tools or attachments to do the job
of heavy duty tool. Don’t use tools for purposes not
intended.
8. Dress properly
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working out-
doors. Wear protective hair covering to contain long
hair.
9. Use safety glasses
Also use face or dust mask if cutting operation is
dusty.
10.Do not abuse cord
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and sharp
edges.
11.Secure work
Use clamps or a vise to hold work. It’s safer than using
your hand and it frees both hands to operate tool.
12.Do not overreach
Keep proper footing and balance at all times.
13.Maintain tools with care
Keep tools sharp and clean for better and safer per-
formance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
14.Disconnect tools
When not in use, before servicing, and when chan-
ging accessories such as blades, bits and cutters.
15.Remove adjusting keys and wrenches
Form the habit of checking to see that keys and adjus-
ting wrenches are removed from tool before turning
it on.
16.Avoid unintentional starting
Do not carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
17.Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
18.Stay alert
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
19.Check damaged parts
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to deter-
mine that it will operate properly and perform its
intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated
elsewhere in this instructions manual. Have defective
switches replaced by an authorized center. Do not
use tool if switch does not turn it on and off.
20.Warning
The use of any other accessory or attachment other
than recommended in this operation instructions or
the catalog may present a risk of personal injury.
21.Have your tool repaired by an expert
This electric appliance is in accordance with the rele-
vant safety rules repairing of electric apliances may be
carried out only by experts otherwise it may cause
considerable danger for the user.
22.Connect the dust extraction device
Whenever there are facilities for fitting a dust extrac-
tion system, make sure it is connected and used.
BEFORE YOU OPERATE THE MACHINE
1. Make sure the switch is “OFF” before you plug in the
machine.
2. Keep the cable away from moving parts.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN
•
Interruption in the mains plug, mains lead or mains
lead damage.
•
Defect switch.
•
Smoke or stench of scorched isolation.
OPERATION
Before setting up, repair or maintenance of the
appliance you must always turn off the operating
switch and pull out the mains plug!
Fig. B
BEFORE INITIAL OPERATION
•
Check if the rated voltage and rated frequency of the
mains supply correspond to the details of the type plate.
•
Place the workbench on a stable and even base.
OPERATION
Fig. A - B
•
To adjust the planing depth, turn the control knob
(
Fig. A
, A) in a clockwise direction. On the control
knob there is a pointer (
Fig. A
, A) which shows the pla-
ning depth in mm. Turn the control knob until the
desired planing depth is shown.
6
Powercraft
SPARE PARTS LIST PP-82
REF NR
DESCRIPTION
POWERCRAFT NR
5
CARBON BRUSH
406445
6
SWITCH
406442
17
ADJUSTING PLATE
406506
20
STATOR
406447
28
ROTOR
406446
34
UPPER PRESSING BOARD
406502
35
BLADE
319266
36
LOWER PRESSING BOARD
406503
47
DRIVING BELT
406443
48
BASE
406449
49
LEFT COVER
406444
-
DUST BAG
406504