Poulan Pro PR17542STA Скачать руководство пользователя страница 20

20

TRANSAXLE GEAR SHIFT LEVER NEUTRAL
ADJUSTMENT (See Fig. 23)

The transaxle should be in neutral when the gear shift lever
is in neutral (N) (lock gate) position. The adjustment is preset
at the factory; however, if adjustment is needed, proceed as
follows:

Make sure transaxle is in neutral (N).

NOTE:

  When the tractor rear wheels move freely, the

transaxle is in neutral.

Loosen adjustment bolt in front of the right rear wheel.

Position the gear shift lever in the neutral (N) position.

Tighten adjustment bolt securely.

NOTE:

  If additional clearance is needed to get to adjustment

bolt, move mower deck height to the lowest position.

ADJUSTMENT
BOLT

NEUTRAL
LOCK GATE

GEARSHIFT LEVER

FIG. 23

SERVICE AND ADJUSTMENTS

1-1/2"

NUT "A"

OPERATING
ARM

JAM NUT

FIG. 21

FIG. 22

WITH PARKING BRAKE

"ENGAGED"

TRANSAXLE
PULLEY

STATIONARY
IDLER

CLUTCHING
IDLER

ENGINE
PULLEY

TO REPLACE MOTION DRIVE BELT
(See Fig. 22)

Park the tractor on level surface.  Engage parking brake.  For
assistance, there is a belt installation guide decal on bottom
side of left footrest.

Remove mower (See “TO REMOVE MOWER” in this
section of this manual.)

Remove belt from stationary idler and clutching idler.

Pull belt slack toward rear of tractor.  Remove belt
upwards from transaxle pulley by deflecting belt keep-
ers.

Pull belt toward front of tractor and remove downwards
from around engine pulley.

Install new belt by reversing above procedure.

TO ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at
high speed  in highest gear on a level dry concrete or paved
surface, then brake must be adjusted.

Depress clutch/brake pedal and engage parking brake.

Measure distance between brake operating arm and nut
“A” on brake rod.

If distance is other than 1-1/2", loosen jam nut and turn
nut “A” until distance becomes 1-1/2".  Retighten jam nut
against nut “A”.

Road test tractor for proper stopping distance as stated
above.  Readjust if necessary.  If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary.  Contact your nearest  au-
thorized service center/department.

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 20)

The mower blade drive belt may be replaced without tools.
Park the tractor on level surface.  Engage parking brake.

BELT REMOVAL

Remove mower from tractor (See “TO REMOVE
MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt
guides.

Install mower in reverse order of removal instructions.

IDLER
PULLEYS

MANDREL
PULLEYS

FIG. 20

Содержание PR17542STA

















































Отзывы: